Indesit CI6V E97 A1 HA, Руководство по эксплуатации

Страница: 28 / 84

28
GB
Switching the appliance off
Disconnect your appliance from the electricity supply before
carrying out any work on it.
Cleaning the oven
! Never use steam cleaners or pressure cleaners on the
appliance.
• Clean the glass part of the oven door using a sponge and
a non-abrasive cleaning product, then dry thoroughly
with a soft cloth. Do not use rough abrasive material or
sharp metal scrapers as these could scratch the surface
and cause the glass to crack.
• The stainless steel or enamel-coated external parts and
the rubber seals may be cleaned using a sponge which
has been soaked in lukewarm water and neutral soap.
Use specialised products for the removal of stubborn
stains. After cleaning, rinse and dry thoroughly. Do not
use abrasive powders or corrosive substances.
• The inside of the oven should ideally be cleaned after
each use, while it is still lukewarm. Use hot water and
detergent, then rinse well and dry with a soft cloth. Do
not use abrasive products.
• The accessories can be washed like everyday crockery,
and are even dishwasher safe.
• Dirt and grease should be removed from the control panel
using a non-abrasive sponge or a soft cloth.
•
Stainless steel can be marked by hard water that has
been left on the surface for a long time, or by aggressive
detergents that contain phosphorus. We recommend
that the steel surfaces are rinsed well then dried
thoroughly.
Inspecting the oven seals
Check the door seals around the oven regularly. If the seals
are damaged, please contact your nearest After-sales Service
Centre. We recommend that the oven is not used until the
seals have been replaced.
Replacing the oven light bulb
1. After disconnecting the oven from the electricity mains,
remove the glass lid covering the lamp socket (see fi gure).
2. Unscrew the light bulb and
replace it with a similar one: voltage
230 V, wattage 25 W, cap E 14.
3. Replace the lid and reconnect the
oven to the electricity supply.
! Do not use the oven lamp as/for
ambient lighting.
Cleaning the glass ceramic hob
! Do not use abrasive or corrosive detergents (for example,
products in spray cans for cleaning barbecues and ovens),
stain removers, anti-rust products, powder detergents or
sponges with abrasive surfaces: these may scratch the surface
beyond repair.
• It is usually suffi
cient simply to wash the hob using a damp
sponge and dry it with absorbent kitchen roll.
• If the hob is particularly dirty, rub it with a special glass
ceramic cleaning product, then rinse well and dry
thoroughly.
• To remove more stubborn dirt, use a suitable scraper (this is
not supplied with the appliance). Remove spills as soon as
possible, without waiting for the appliance to cool, to avoid
residues forming crusty deposits. You can obtain excellent
results by using a rustproof steel wire sponge - specifi cally
designed for glass ceramic surfaces - soaked in soapy water.
• If plastic or sugary substances have accidentally been
melted on the hob, remove them immediately with the
scraper, while the surface is still hot.
• Once it is clean, the hob may be treated with a special
protective maintenance product: the invisible fi lm left by
this product protects the surface from drips during cooking.
This maintenance should be carried out while the appliance
is warm (not hot) or cold.
• Always remember to rinse the appliance well with clean
water and dry it thoroughly: residues can become
encrusted during subsequent cooking processes.
Care and maintenance
Glass ceramic hob cleaners Available from
Window scraper Razor blade
scrapers DIY Stores
Replacement blades DIY Stores,
supermarkets,
chemists
COLLO luneta
HOB BRITE
Hob Clean
SWISSCLEANER Boots, Co-op stores,
department stores, Regional
Electricity Company shops,
supermarkets
Assembling the sliding rack kit
To assemble the sliding racks:
1. Remove the two frames,
lifting them away from the
spacers A (see fi gure).
2. Choose which shelf
to use with the sliding
rack. Paying attention to
the direction in which
the sliding rack is to be
extracted, position joint
B and then joint C on the
frame.
A
B
C
Lef t
guide rail
Right guide
rail
Dire
ctio
n
of
extra
ct
io
n