Mounting the Remote Control
12
(1) Place the bracket on the wall depending on the wall material as follows, then mount it in the desired mounting position.
If mounted either in plywood paneling 5 mm
or less in thickness or in gypsum board:
A) In plywood paneling, drill
holes with a diameter of 6
mm; in gypsum board, drill
holes with a diameter of 5
mm.
B) Using a hammer, gently
drive the plastic anchors
into the holes.
C) Fasten the bracket securely
to the anchors using wood
screws. As you tighten the
screws, they are hard to turn at first, then gradually
get easier to turn, and then are hard to turn again.
Bracket
Wood Screw
Plastic Anchor
6 mm
dia.
(2) Align the remote control
unit with the bracket and
then push it down onto the
bracket.
Remote
Control Unit
Bracket
Installing the Water Supply Hose (Water shutoff valve side)
In the case of
water supply
from the wall
In the case of
water supply
from the floor
Clip
Clip
Water
Shutoff Valve
Water
Shutoff Valve
Water
Shutoff Valve
Water Supply Hose
Water Supply Hose
O-ring
Clip
(1) Remove the cap from the end of the water supply hose, then
insert it in the water supply outlet of the water shutoff valve.
See NOTE 11.
See NOTE 18.
(2) Fasten the clip securely.
See NOTE 19.
本体ホース付け5.eps
O-ring
Water Supply Hose
Water Supply Outlet
Water Shutoff Valve
Cap
(3) Install the clip in the same way as on the
body supply water inlet side, making sure
the two sides of the clip fit securely and lock
together.
See NOTE 20.
See Reference
1.
クリップ付ける2.eps
カチッ
Click
Clip
Bend the clip
around.
クリップ付ける.eps
Water Supply Hose
Clip
Water Shutoff Valve
(3) Open the remote control unit's lower half to expose the
additional controls. Press and hold the "Hr" button, and
release the button when the current hour is shown.
Make sure AM or PM appears, as appropriate.
Repeat this procedure with the
"Min" button to set the current
minute.
10
Connecting the Power Supply
1. Insert the power plug in
the receptacle.
See NOTE 21.
2. Confirm that the system
has been turned on.
Confirm that the power
lamp on the body is lit.
If the power lamp of the body does
not light up, press the reset button
on the power plug and make sure
the lamp lights up in green.
Wait for around 10 seconds before
inserting the power plug again.
*
*
プラグ差し込み.eps
Power Plug
Power Lamp
Connect the product to a
properly grounded outlet only.
There is danger of electric shock if a
breakdown or current leakage occurs.
When a three-slot receptacle is
needed, contact a licenced electrician.
*
*
EARTH
WARNING
(1) Open the back
cover of the remote
control unit and
insert the batteries
(two AA size
batteries).
See NOTE 22.
(2) Place the remote
control unit in the
position you would
like it to be in, sit
down on the toilet
seat and press the
stop switch. If you
hear an electronic
"beep" sound from
the body.
Positioning the
Remote Control Unit
If mounted in concrete or on block bed:
A) Drill holes with a diameter
of 6 mm and a depth of
approximately 33 mm .
B) Using a hammer, gently drive
the plastic anchors into the
holes.
C) Fasten the bracket securely
to the anchors using wood
screws.
If mounted in plywood
paneling 5 mm or
greater in thickness:
Fasten the bracket to the
wall with the wood screws.
11
Battery
Back Cover
⊕
⊖
⊖
⊕
Installation
Diagram
Bracket
Wood Screw
Plastic Anchor
6 mm dia.
33 mm
Wood
Screw
Bracket
9
Fit the clip securely.
If it does not fit tightly, there
could be water leakage.
*
NOTE 19
Fit the ends of the clip
together, engaging them
until a click sound is heard.
If it does not fit tightly, there
could be water leakage.
*
NOTE 20
Do not bend the water supply
hose at a sharp angle.
There is danger of its becoming
damaged and leaking water.
It could also cause the toilet
not to flush properly.
*
NOTE 18
Be sure to turn on the power
only after installation of the
product is completed.
If the power plug does not light
up, press the reset button and
check to make sure the power
lamp lights up.
Do not insert the power plug in
the receptacle while touching
the toilet seat. The shower
nozzle (posterior, bidet) may
not extend if you do.
If the shower nozzle does not
extend, pull out the power plug,
then insert it again without
touching the toilet seat.
●
●
●
NOTE 21
Install the batteries with
the positive and negative
poles facing the correct
direction in accordance
with the marks on the
remote control unit case.
Do not use old and new
batteries together.
●
●
NOTE 22
Water will spray from the
nozzle if the Shower or
Bidet switch is pressed,
so exercise caution.
Check to make sure there
is enough space above the
remote controller to mount
or remove the controller at
its mounting position.
●
●
NOTE 23
Required
space
See NOTE 23.
