Installing the Water Supply Hose (Body Side)
7
ホース取付（本体）.eps
Installation
Diagram
Water Supply
Inlet on Body
Install the water
supply hose
in a direction
so that it is
not bent when
connected.
Clip
Protective Cap
Water Supply Hose
(3) Fit the clip over the end of the water supply hose and the
body water supply inlet securely.
See NOTE 12.
(1) Remove the protective cap from
the body water supply inlet.
(2) Insert the end of the water
supply hose in the water supply
inlet of the body.
See NOTE 11.
(4) Bend the clip around and
fasten the water supply hose
and the body water supply
inlet securely together with it.
After installation, turn the
clip's open portion so it fits in
and locks together with the
other end.
See NOTE 13.
See Reference
2.
Click
Clip
Bend the clip around.
Click
ホース取付2.eps
Clip
Protective Cap
O-ring
Water Supply
Inlet on Body
Water Supply Hose
Mounting the Toilet Bowl
6
(1) Insert the drain pipe of the toilet bowl in the rubber drain socket joint,
then position thetoilet bowl with the front end raised up and loose.
See NOTE 7.
(2) Slowly put down the front of the toilet bowl. Fit the fixing fasteners of
the mounting base and toilet bowl.
(3) Lower the front end of the toilet bowl until the clicking sound stops.
This operation applies pressure to the mounting fastener. Continue to
push down on the front end of the toilet bowl until the clicking sound stops
and the toilet bowl is in contact with the floor.
(4) Swing the toilet bowl lightly to make sure the front end is fastened
securely to the floor.
If the toilet bowl is not fastened securely, remove it, loosen the
T-bolts of the mountin gfastener in the floor about 5 turns, then
repeat the installation procedure.
If positioning of the toilet deviates from the correct position, lift up
the front end of thetoilet bowl, position it again and push the toilet
down in that position to fasten it again.
See Reference
1.
(5) Fasten the rear end of the toilet bowl using the washers and mounting
nuts supplied, and then install the decorator caps.
See NOTE 7.
See NOTE 8.
*When reinstalling the toilet bowl
See NOTE 9.
See NOTE 10.
See Reference
1.
*
*
*
06M038
化粧キャップ付ける.eps
Decorator Cap
Flush Water Inlet
Mounting Nut
Washer
Installing the Body
2. Install the flat packings.
Install the flat
packings on
the 2 mounting
bolts on the
bottom of the
body.
Install the flat
packings so
that the body
cover does not
get any flaw.
*
パッキン取付1.eps
Mounting Bolt
Flat Packing
3. Install the body on the toilet.
Place the
mounting bolts
on the bottom
of the body in
the 2 mounting
holes in the
back of the
toilet bowl to
install the body.
See NOTE 15.
See NOTE 16.
タンク取付2.eps
Mounting Hole
Mounting Bolt
Body
4. Fasten the body.
(1) Make sure the
mounting nuts are
open.
If they are closed, pull
on them as shown
until they click.
Cナット開く.eps
Closed State Open State
(2) Place the new
mounting nuts on
the mounting bolts.
See NOTE 17.
Cナット通す.eps
Toilet
Bowl
Mounting Bolt
Mounting
Nut
(3) Push up on the
new mounting nuts
to close
them.
(4) Turn the new
mounting nuts by
hand to
tighten
them.
Mounting Fastener
(Mounted on the toilet bowl)
Drain Pipe
Rubber Drain Joint
Insert
Push Down
Fixing fastener
(on the mounting base)
Installation
Diagram
Flat Packing
New Mounting Nut
1. Remove the protective tape and protective cap.
Remove the protective tape from the toilet bowl,
and then remove the protective cap from the body.
See NOTE 14.
施工
時
～
1.eps
<Body>
Protective Cap
施工時2.eps
<Toilet Bowl>
Protective Tape
Plate
(metal)
Cナット押込.eps
Push up.
Cナット締付.eps
Tighten
8
Do not place the toilet bowl on
the pedestal or drain socket.
Otherwise it may damage the socket or packing
gland, which may cause water leakage.
*
NOTE 7
Do not tighten the screws
tootightly against the ceramic.
There is danger of the ceramiccracking.
*
NOTE 8
Avoid damaging or allowing foreign
matter to enter the flush water inlet.
NOTE 9
Reference 1
1) Remove decorator caps, mounting nuts and
washers from the rear of the toilet bowl.
2) Raise the toilet bowl
up slowly.
3) Loosen the T-bolts in
the fastener at the rear
of the toilet bowl about
5 turns, then mount
the toilet once again.
Tボルト調整.eps
T-bolts
Loosen them about 5 turns.
When removing the toilet bowl, be
careful not to damage the toilet
with the toilet bowl mounting
bolts in the rear of the toilet bowl.
NOTE 10
Be careful not to damage the O-ring.
Water may leak if the O-ring is broken or damaged.
Remove the cap on the water supply
hose immediately before connecting
it to the water shutoff valve.
There is danger of dirt, etc. getting inside the
water supply hose while the work is proceeding,
making it difficult to shut off the flow of water.
●
*
●
*
NOTE 11
Thoroughly insert the clip on
the front or from the back.
If it is fitted at a slant, the clip may become bent out
of shape and might not fasten the hose securely.
Fit the clip securely.
If it does not fit tightly, there could be water leakage.
●
*
●
*
NOTE 12
Fit the ends of the clip together,
engaging them until a click
sound is heard.
If the clip does not fit tightly, there could be water leakage.
*
NOTE 13
Do not remove the (metal) plate.
There is danger of water leakage.
*
NOTE 14
Do not take hold of the flush
handle to lift the body.
The body or the flush handle could become damaged.
*
NOTE 15
Make sure the body is sitting
firmly on the toilet bowl.
There is danger of water leaking from the water inlet to
the toilet if the body is not seated firmly on the toilet.
*
NOTE 16
Tighten the mounting nuts gradually,
alternating the tightening between
the left and right sides to keep from
putting too much strain on one side.
Uneven tightening could cause water leakage.
The black rubber portion of the
new mounting nuts is the top.
Screw the nuts on in the direction
indicated by the arrow mark.
If it is difficult to tighten the nuts
by hand, tighten them further
using a 17 mm wrench.
●
*
●
●
NOTE 17
Reference 2
When removing the clip, hold
the clip with your
fingers and insert
the flat-blade
screwdriver. Then,
push it downward
as shown right.
●
クリップ外す.eps
Push
Clip
