Inalto ESL60D2S, Руководство пользователя

Страница: 19 / 28

19
CHANGING A LIGHT GLOBE
If the light lamp needs replacing, proceed as follows:
• Slide out the front panel for easier access and remove the two aluminium mesh filters
• Push out the lamp by hand from its back, pull out the lamp connecting lines together;
• Open the protection cover as shown in the picture below, and unplug the connected plastic shell
to replace a new lamp.
Please contact our After Sales Service Team
if you need assistance.
15
15
Cleaning and maintenance
CAUTION!
• Before cleaning the rangehood or carrying out
maintenance, make sure the operation and
light switches are set to the “ 0 ” position and
the rangehood is disconnected from the power
supply.
• It is important to clean the filters regularly as oil
and food residues can become a fire hazard.
• Never use a steam cleaner to clean any part of
the rangehood.
Cleaning the rangehood exterior
Wipe the exterior surface of the rangehood
regularly using a soft cloth moistened with a
household solvent such as methylated spirits, or
with a sponge dampened with water and a little
non-abrasive liquid detergent.
Cleaning the grease filters
The aluminium mesh filters must be cleaned
regularly in order to prevent a fire hazard. Regular
cleaning also ensures better efficiency, as
grease and grime can impede the airflow. We
recommend cleaning them at least every two
months.
• Push in the plastic opening latch and take the
filters out of their frames (Fig. 14).
Fig. 14
• Wash the filters thoroughly in warm, soapy
water, leaving them to soak for best results.
Rinse with warm water and leave to dry.
NOTE: The aluminum panels may slightly
change colour after several washes.
This is not a fault and no cause
for concern. It does not affect
performance and does not warrant
replacement of these parts.
Charcoal filters
If you are using the rangehood with the air
recirculating back into the room, the charcoal
filters which were supplied with the rangehood
would have already been installed.
A charcoal filter absorbs cooking odours and
must be changed regularly. How often you need
to change the filters depends on your usage. We
recommend changing them every three to six
months. An activated charcoal filter cannot be
washed or recycled; it must be replaced with a
new one.
To obtain replacement filters, contact our after
sales support line and arrange for purchase (see
page 18 for details).
NOTE:
The suction power will be lowered
with charcoal filters installed.
To remove and/or install new filters, please see
page 11.
Replacing a light bulb
If the light bulb needs replacing, proceed as
follows:
• Slide out the front panel for easier access and
remove the two aluminium mesh filters (Fig. 15).
• Carefully turn the bulb in anticlockwise
direction and remove (Fig. 16).
• Replace the bulb with one of the same type
and wattage (E14, 28W), as illustrated below
(Fig. 17).
OTHER USEFUL INFORMATION
Fig. 15
Fig. 16
Fig. 17
15
Cleaning and maintenance
CAUTION!
• Before cleaning the rangehood or carrying out
maintenance, make sure the operation and
light switches are set to the “ 0 ” position and
the rangehood is disconnected from the power
supply.
• It is important to clean the filters regularly as oil
and food residues can become a fire hazard.
• Never use a steam cleaner to clean any part of
the rangehood.
Cleaning the rangehood exterior
Wipe the exterior surface of the rangehood
regularly using a soft cloth moistened with a
household solvent such as methylated spirits, or
with a sponge dampened with water and a little
non-abrasive liquid detergent.
Cleaning the grease filters
The aluminium mesh filters must be cleaned
regularly in order to prevent a fire hazard. Regular
cleaning also ensures better efficiency, as
grease and grime can impede the airflow. We
recommend cleaning them at least every two
months.
• Push in the plastic opening latch and take the
filters out of their frames (Fig. 14).
Fig. 14
• Wash the filters thoroughly in warm, soapy
water, leaving them to soak for best results.
Rinse with warm water and leave to dry.
NOTE: The aluminum panels may slightly
change colour after several washes.
This is not a fault and no cause
for concern. It does not affect
performance and does not warrant
replacement of these parts.
Charcoal filters
If you are using the rangehood with the air
recirculating back into the room, the charcoal
filters which were supplied with the rangehood
would have already been installed.
A charcoal filter absorbs cooking odours and
must be changed regularly. How often you need
to change the filters depends on your usage. We
recommend changing them every three to six
months. An activated charcoal filter cannot be
washed or recycled; it must be replaced with a
new one.
To obtain replacement filters, contact our after
sales support line and arrange for purchase (see
page 18 for details).
NOTE:
The suction power will be lowered
with charcoal filters installed.
To remove and/or install new filters, please see
page 11.
Replacing a light bulb
If the light bulb needs replacing, proceed as
follows:
• Slide out the front panel for easier access and
remove the two aluminium mesh filters (Fig. 15).
• Carefully turn the bulb in anticlockwise
direction and remove (Fig. 16).
• Replace the bulb with one of the same type
and wattage (E14, 28W), as illustrated below
(Fig. 17).
OTHER USEFUL INFORMATION
Fig. 15
Fig. 16
Fig. 17
Replacing the light bulb
If the light lamp needs replacing, proceed as follows:
• Slide out the front panel for easier access and
remove the two aluminium mesh filters (Fig. 15).
• Push out the lamp by hand from its back, pull out the lamp
connecting lines together;
• Open the protection cover as shown in the picture below,
and unplug the connected plastic shell to replace a new lamp.
Open the protective cover
Unplug the lines
15
15
Cleaning and maintenance
CAUTION!
• Before cleaning the rangehood or carrying out
maintenance, make sure the operation and
light switches are set to the “ 0 ” position and
the rangehood is disconnected from the power
supply.
• It is important to clean the filters regularly as oil
and food residues can become a fire hazard.
• Never use a steam cleaner to clean any part of
the rangehood.
Cleaning the rangehood exterior
Wipe the exterior surface of the rangehood
regularly using a soft cloth moistened with a
household solvent such as methylated spirits, or
with a sponge dampened with water and a little
non-abrasive liquid detergent.
Cleaning the grease filters
The aluminium mesh filters must be cleaned
regularly in order to prevent a fire hazard. Regular
cleaning also ensures better efficiency, as
grease and grime can impede the airflow. We
recommend cleaning them at least every two
months.
• Push in the plastic opening latch and take the
filters out of their frames (Fig. 14).
Fig. 14
• Wash the filters thoroughly in warm, soapy
water, leaving them to soak for best results.
Rinse with warm water and leave to dry.
NOTE: The aluminum panels may slightly
change colour after several washes.
This is not a fault and no cause
for concern. It does not affect
performance and does not warrant
replacement of these parts.
Charcoal filters
If you are using the rangehood with the air
recirculating back into the room, the charcoal
filters which were supplied with the rangehood
would have already been installed.
A charcoal filter absorbs cooking odours and
must be changed regularly. How often you need
to change the filters depends on your usage. We
recommend changing them every three to six
months. An activated charcoal filter cannot be
washed or recycled; it must be replaced with a
new one.
To obtain replacement filters, contact our after
sales support line and arrange for purchase (see
page 18 for details).
NOTE:
The suction power will be lowered
with charcoal filters installed.
To remove and/or install new filters, please see
page 11.
Replacing a light bulb
If the light bulb needs replacing, proceed as
follows:
• Slide out the front panel for easier access and
remove the two aluminium mesh filters (Fig. 15).
• Carefully turn the bulb in anticlockwise
direction and remove (Fig. 16).
• Replace the bulb with one of the same type
and wattage (E14, 28W), as illustrated below
(Fig. 17).
OTHER USEFUL INFORMATION
Fig. 15
Fig. 16
Fig. 17
15
Cleaning and maintenance
CAUTION!
• Before cleaning the rangehood or carrying out
maintenance, make sure the operation and
light switches are set to the “ 0 ” position and
the rangehood is disconnected from the power
supply.
• It is important to clean the filters regularly as oil
and food residues can become a fire hazard.
• Never use a steam cleaner to clean any part of
the rangehood.
Cleaning the rangehood exterior
Wipe the exterior surface of the rangehood
regularly using a soft cloth moistened with a
household solvent such as methylated spirits, or
with a sponge dampened with water and a little
non-abrasive liquid detergent.
Cleaning the grease filters
The aluminium mesh filters must be cleaned
regularly in order to prevent a fire hazard. Regular
cleaning also ensures better efficiency, as
grease and grime can impede the airflow. We
recommend cleaning them at least every two
months.
• Push in the plastic opening latch and take the
filters out of their frames (Fig. 14).
Fig. 14
• Wash the filters thoroughly in warm, soapy
water, leaving them to soak for best results.
Rinse with warm water and leave to dry.
NOTE: The aluminum panels may slightly
change colour after several washes.
This is not a fault and no cause
for concern. It does not affect
performance and does not warrant
replacement of these parts.
Charcoal filters
If you are using the rangehood with the air
recirculating back into the room, the charcoal
filters which were supplied with the rangehood
would have already been installed.
A charcoal filter absorbs cooking odours and
must be changed regularly. How often you need
to change the filters depends on your usage. We
recommend changing them every three to six
months. An activated charcoal filter cannot be
washed or recycled; it must be replaced with a
new one.
To obtain replacement filters, contact our after
sales support line and arrange for purchase (see
page 18 for details).
NOTE:
The suction power will be lowered
with charcoal filters installed.
To remove and/or install new filters, please see
page 11.
Replacing a light bulb
If the light bulb needs replacing, proceed as
follows:
• Slide out the front panel for easier access and
remove the two aluminium mesh filters (Fig. 15).
• Carefully turn the bulb in anticlockwise
direction and remove (Fig. 16).
• Replace the bulb with one of the same type
and wattage (E14, 28W), as illustrated below
(Fig. 17).
OTHER USEFUL INFORMATION
Fig. 15
Fig. 16
Fig. 17
Replacing the light bulb
If the light lamp needs replacing, proceed as follows:
• Slide out the front panel for easier access and
remove the two aluminium mesh filters (Fig. 15).
• Push out the lamp by hand from its back, pull out the lamp
connecting lines together;
• Open the protection cover as shown in the picture below,
and unplug the connected plastic shell to replace a new lamp.
Open the protective cover
Unplug the lines
15
15
Cleaning and maintenance
CAUTION!
• Before cleaning the rangehood or carrying out
maintenance, make sure the operation and
light switches are set to the “ 0 ” position and
the rangehood is disconnected from the power
supply.
• It is important to clean the filters regularly as oil
and food residues can become a fire hazard.
• Never use a steam cleaner to clean any part of
the rangehood.
Cleaning the rangehood exterior
Wipe the exterior surface of the rangehood
regularly using a soft cloth moistened with a
household solvent such as methylated spirits, or
with a sponge dampened with water and a little
non-abrasive liquid detergent.
Cleaning the grease filters
The aluminium mesh filters must be cleaned
regularly in order to prevent a fire hazard. Regular
cleaning also ensures better efficiency, as
grease and grime can impede the airflow. We
recommend cleaning them at least every two
months.
• Push in the plastic opening latch and take the
filters out of their frames (Fig. 14).
Fig. 14
• Wash the filters thoroughly in warm, soapy
water, leaving them to soak for best results.
Rinse with warm water and leave to dry.
NOTE: The aluminum panels may slightly
change colour after several washes.
This is not a fault and no cause
for concern. It does not affect
performance and does not warrant
replacement of these parts.
Charcoal filters
If you are using the rangehood with the air
recirculating back into the room, the charcoal
filters which were supplied with the rangehood
would have already been installed.
A charcoal filter absorbs cooking odours and
must be changed regularly. How often you need
to change the filters depends on your usage. We
recommend changing them every three to six
months. An activated charcoal filter cannot be
washed or recycled; it must be replaced with a
new one.
To obtain replacement filters, contact our after
sales support line and arrange for purchase (see
page 18 for details).
NOTE:
The suction power will be lowered
with charcoal filters installed.
To remove and/or install new filters, please see
page 11.
Replacing a light bulb
If the light bulb needs replacing, proceed as
follows:
• Slide out the front panel for easier access and
remove the two aluminium mesh filters (Fig. 15).
• Carefully turn the bulb in anticlockwise
direction and remove (Fig. 16).
• Replace the bulb with one of the same type
and wattage (E14, 28W), as illustrated below
(Fig. 17).
OTHER USEFUL INFORMATION
Fig. 15
Fig. 16
Fig. 17
15
Cleaning and maintenance
CAUTION!
• Before cleaning the rangehood or carrying out
maintenance, make sure the operation and
light switches are set to the “ 0 ” position and
the rangehood is disconnected from the power
supply.
• It is important to clean the filters regularly as oil
and food residues can become a fire hazard.
• Never use a steam cleaner to clean any part of
the rangehood.
Cleaning the rangehood exterior
Wipe the exterior surface of the rangehood
regularly using a soft cloth moistened with a
household solvent such as methylated spirits, or
with a sponge dampened with water and a little
non-abrasive liquid detergent.
Cleaning the grease filters
The aluminium mesh filters must be cleaned
regularly in order to prevent a fire hazard. Regular
cleaning also ensures better efficiency, as
grease and grime can impede the airflow. We
recommend cleaning them at least every two
months.
• Push in the plastic opening latch and take the
filters out of their frames (Fig. 14).
Fig. 14
• Wash the filters thoroughly in warm, soapy
water, leaving them to soak for best results.
Rinse with warm water and leave to dry.
NOTE: The aluminum panels may slightly
change colour after several washes.
This is not a fault and no cause
for concern. It does not affect
performance and does not warrant
replacement of these parts.
Charcoal filters
If you are using the rangehood with the air
recirculating back into the room, the charcoal
filters which were supplied with the rangehood
would have already been installed.
A charcoal filter absorbs cooking odours and
must be changed regularly. How often you need
to change the filters depends on your usage. We
recommend changing them every three to six
months. An activated charcoal filter cannot be
washed or recycled; it must be replaced with a
new one.
To obtain replacement filters, contact our after
sales support line and arrange for purchase (see
page 18 for details).
NOTE:
The suction power will be lowered
with charcoal filters installed.
To remove and/or install new filters, please see
page 11.
Replacing a light bulb
If the light bulb needs replacing, proceed as
follows:
• Slide out the front panel for easier access and
remove the two aluminium mesh filters (Fig. 15).
• Carefully turn the bulb in anticlockwise
direction and remove (Fig. 16).
• Replace the bulb with one of the same type
and wattage (E14, 28W), as illustrated below
(Fig. 17).
OTHER USEFUL INFORMATION
Fig. 15
Fig. 16
Fig. 17
Replacing the light bulb
If the light lamp needs replacing, proceed as follows:
• Slide out the front panel for easier access and
remove the two aluminium mesh filters (Fig. 15).
• Push out the lamp by hand from its back, pull out the lamp
connecting lines together;
• Open the protection cover as shown in the picture below,
and unplug the connected plastic shell to replace a new lamp.
Open the protective cover
Unplug the lines