IMT TH36K164 Скачать руководство пользователя страница 45

Страница: 45 / 135

Chapter 6 Tirehand Repair 43

Tirehand Cylinders

The Tirehand uses similar cylinders in all functions. Common disassembly and repair
instructions apply. Check the Parts section for specific information.

CLAMP CYLINDER REMOVAL & INSTALLATION

To remove the clamp cylinder:

Rotate the Tirehand until the clamp cylinder is in a horizontal position.

Extend the cylinder full stroke.

Shut off the carrier vehicle’s engine. Relieve internal hydraulic pressure by cycling the

controls.

Remove the cover from the body (refer to the appropriate body drawing) and disconnect

the hydraulic hoses at the cylinder port block. Cap the hydraulic hoses.

Support the hand assembly with a lifting device and straps capable of supporting the

assembly. Take up slack in the lifting device

Disconnect and cap any hydraulic lines leading to the pad rotation mechanism.

Remove the cylinder rod pin by removing the 3/4-10 cap screws and washer securing the
pin. Drive out the pin.

Support the hand assembly. Remove the two smaller hand/arm pins by removing the 3/4-

10 cap screws securing the pins. Drive out the pins.

Lift the hand assembly away and place on a clean surface. Keep dirt out of the bushing

surfaces.

10 Support the clamp cylinder with a lifting device and straps capable of supporting the

cylinder.

11 Remove the cylinder base pin securing screw and washer. Drive the pin only far enough to

release the cylinder.

12 Lift the cylinder away and repair as necessary.

To install the clamp cylinder:

Position the cylinder in the slings of the lifting device and line up the base end pin boss

and pin. Seat the pin and secure using the 3/4-10 cap screw and washer. Torque to 265 ft-
lb (36.6 kg-m).

Lift the hand assembly with the slings and position the pin bosses in line with the pins.

Drive in the pins and secure using the 3/4-10 hardware. Torque to 265 ft-lb (36.6 kg-m).

Connect the hydraulic hoses to the clamp cylinder and axial rotation motor.

Start the engine. Cycle the CLAMP and PAD controls through at least five cycles to purge

any air trapped in the system. Check for leaks.

Courtesy of Crane.Market

Содержание TH36K164








































































































































Результаты поиска

Содержание TH36K164

Отзывы:

Похожие инструкции для TH36K164

Бренды по названию

Популярные бренды

IMT TH36K164, Руководство пользователя

Результаты поиска

Содержание TH36K164

Отзывы:

Похожие инструкции для TH36K164

Бренды по названию

Популярные бренды