background image

23 

 

 

 

 

WARNING 

If vibration occurs during starting, stop the pump immediately and eliminate the 

cause before starting again. 

11.  Let the engine run for five minutes before the pump is connected to the dewatering system. 
12.  If the engine does not start, press and hold the red handle on the oil-pressure protection. Start 

the engine and release the handle once the engine is running. 

 

 

 

WARNING 

The pump must never pump against a closed shut-off valve! Otherwise there is a 
danger of explosion in the pump or the piping system. 

 

 

 

WARNING 

Dewatering  activities  will  have  an  impact  on  the  surrounding  area  in  which 
water is being extracted from the ground. 
Settling of the ground occurs during groundwater extraction. This can result 
in  grains  of  sand  moving  closer  together,  which  will  have  an  impact  on  the 
ground. 

This can  cause  cracks  in  buildings  and  pipes.  It  can  also  result  in  rotting  of 
wooden  foundation  piles  if  the  groundwater  is  kept  at  a  low  level  for  an 
extended period of time

Before starting a dewatering system, make sure a sound dewatering plan has 
been prepared and that the impact on the surrounding area is clear. 

7.2 Stopping (type1) 

 

1. 

Turn the switch on the control panel to off position (1). 

 

2.  When you suspect that the liquid is beginning to freeze, drain the pump while the medium is still in 

the liquid state. 

3.  Before the pump is shut down, check whether this has an impact on the dewatering system. 
4.  Close the shut-off valve (if present). 
5.  Close the suction shut-off valve.(if present). 

Содержание Yamuna







































Отзывы: