Impulse DO2412R.4909 Скачать руководство пользователя страница 8

Страница: 8 / 21

2. Display Case Setup



SCC® service drop-in refrigerated merchandiser

case consists of two sections: The upper display

case and drop-in refrigerated section.



As both sections make up one conjoined unit, it

is both large and heavy. A team effort is required

for lowering case into the customer supplied

base.



After lowering into base, adjust into position

allowing case to gingerly rest on counter top

without marring.

1. Remove Case From Skid

Caution: Case must always remain supported or

center of gravity may allow case to fall. Slide to

rear of skid and tip backward off skid while

maintaining support.

Note: Illustration below may not exact reflect every

feature or option of your particular case.

Slide

Skid

Out

3. Seal Upper Display Case to Base



NSF® Listed Industrial Grade Silicone Sealant is

recommended.



Clip tip to allow approximately 1/8” to 3/16”

diameter hole.



Beginning at case rear,

run a consistent, solid

bead of silicone

around entire

perimeter.

Drop-In

Refrigerated

Section

Upper

Display

Case

Seal

Along

Here

Seal

Along

Here

INSTALLATION: CASE REMOVAL / CASE SETUP / SEALING UPPER DISPLAY CASE TO BASE

Содержание DO2412R.4909






















Результаты поиска

Содержание DO2412R.4909

Отзывы:

Похожие инструкции для DO2412R.4909

Бренды по названию

Популярные бренды

Impulse DO2412R.4909, Инструкция по установке и эксплуатации

Результаты поиска

Содержание DO2412R.4909

Отзывы:

Похожие инструкции для DO2412R.4909

Бренды по названию

Популярные бренды