Impulse DO2412R.4909 Скачать руководство пользователя страница 3

Страница: 3 / 21

OVERVIEW



These Structural Concepts merchandisers are

designed to merchandise packaged products at 41 °F

[5 °C] or less product temperatures.



Cases should be installed and operated according to

this operating manual’s instructions to ensure proper

performance.



Improper use will void warranty.

TYPE 1 vs. TYPE 2 CONDITIONS

This unit is designed for the display of products in ambient

store conditions where temperatures and humidity are

maintained within a specific range.



For Type 1 Conditions (most cases): ambient

conditions are to be at 55% maximum humidity and

maximum temperatures of 75 °F [24 °C].



For Type 2 Conditions: ambient conditions are to be at

55% maximum humidity and maximum temperatures of

80 °F [27 °C].



If unsure if unit is designed for Type 1 or 2, see tag

next to serial label. See

SERIAL LABEL LOCATION &

INFORMATION LISTED / TECH INFO & SERVICE

section in this manual for sample serial labels.

COMPLIANCE



Performance issues when in violation of applicable

NEC, federal, state and local electrical and plumbing

codes are not covered by warranty.



See below compliance guideline.

WARNINGS



This page contains important warnings to prevent injury

or death. Please read carefully!

WARNING

Hazardous moving parts. Do not operate unit with covers removed.

Fan blades may be exposed when deck panel is removed.

Disconnect power before removing deck panel.

WARNING

Risk of electric shock. Disconnect power before servicing unit.

CAUTION! More than one source of electrical supply is

employed with units that have separate circuits.

Disconnect ALL ELECTRICAL SOURCES before servicing.

WARNING

Condensate Pan is Hot!

Disconnect and allow to cool

before cleaning or removing from case.

WARNING

ELECTRICAL

HAZARD

WARNING

KEEP

HANDS

CLEAR

WARNING

HOT

SURFACE

COMPLIANCE

This equipment MUST be installed in compliance with

all applicable NEC, federal, state and local

electrical and plumbing codes.

OVERVIEW / TYPE / COMPLIANCE / WARNINGS / PRECAUTIONS / WIRING / PLUGS - PAGE 1 of 2

WARNING: This product can expose you to chemicals, including

Urethane (Ethyl Carbamate), which are known to the state of

California to cause cancer and birth defects or other reproductive

harm. For more information go to P65Warnings.ca.gov.

Содержание DO2412R.4909






















Результаты поиска

Содержание DO2412R.4909

Отзывы:

Похожие инструкции для DO2412R.4909

Бренды по названию

Популярные бренды

Impulse DO2412R.4909, Инструкция по установке и эксплуатации

Результаты поиска

Содержание DO2412R.4909

Отзывы:

Похожие инструкции для DO2412R.4909

Бренды по названию

Популярные бренды