GB-8
3. Empty the fuel tank and screw the tank cap back on.
4. After the tank has been emptied, start the engine.
5. Let the engine idle until it stops to free the carburettor
from fuel.
6. Let the engine cool down (about 5 minutes).
7. Remove the spark plug using a spark plug wrench.
8. Fill a tea spoon of pure 2-stroke oil into the combustion
chamber. Pull the starter rope several times slowly to
distribute the oil inside the engine. Put the spark plug
back in.
9. Store the device in a cool, dry place where it is protected
from open flames and sources of heat as flow heaters,
oil-fired boilers etc.
REOPERATION
1. Remove the spark plug.
2. Pull the starter rope quickly to its full extent to remove
any remaining oil from the combustion chamber.
3. Clean the spark plug and check the gap. Replace the
plug if required.
4. Prepare the device for operation.
5. Fill the tank with the proper fuel/oil mixture. See chapter
‘Fuels and lubricants’
.
SPARE PARTS
Please contact our service department if you need acces-
sories or spare parts.
When working with this machine, do not use spare parts
other than those recommended by us. Using spare parts not
recommend by us can result in serious injuries to persons
or damage to the machine.
WASTE DISPOSAL AND ENVIRONMENTAL
PROTECTION
Never pour remainders of chain lubricant or 2-stroke fuel
mixture in the drain or sewerage system or soil, but dispose
of it in a proper, environmentally friendly way, e.g., at a
special collecting point or dump.
If your device should become useless somewhere in the
future or you do not need it any longer, do not dispose
of the device together with your domestic refuse, but
dispose of it in an environmentally friendly manner.
Thoroughly empty the oil/lubricant and fuel tanks and
dispose of the remainders at a special collecting point
or dump. Please also dispose of the device itself at an
according collecting/recycling point. By doing so, plastic
and metal parts can be separated and recycled. Informa-
tion concerning the disposal of materials and devices are
available from your local administration.
WARRANTY
For this petrol tool, the company provides the end user
- independently from the retailer‘s obligations resulting
from the purchasing contract - with the following war-
ranties:
The warranty period is 24 months beginning from the
hand-over of the device which has to be proved by the
original purchasing document. For commercial use and
use for rent, the warranty period is reduced to 12 months.
Wearing parts and defects caused by the use of not fitting
accessories, repair with parts that are no original parts
of the manufacturer, use of force, strokes and breaking
as well as mischievous overloading of the motor are
excluded from this warranty. Warranty replacement does
only include defective parts, not complete devices. War-
ranty repair shall exclusively be carried out by authorized
service partners or by the company‘s customer service.
In the case of any intervention of not authorized person-
nel, the warranty will be held void.
All postage or delivery costs as well as any other subse-
quent expenses will be borne by the customer.
REPAIR SERVICE
Please contact your nearest Lagerhaus specialised
workshop.
You can find a Lagerhaus specialised workshop in your
vicinity in the Internet at „www.lagerhaus.at“.
Содержание BT 4309
Страница 4: ...Abb 1 Abb 2 Abb 3 Abb 7 Abb 8 Abb 9 Abb 10 Abb 4 Abb 5 3 Abb 6 Abb 11 Abb 12 B C E F 17 cm ...
Страница 5: ...Abb 18 Abb 15 Abb 16 Abb 19 b Abb 21 4 Abb 13 Abb 14 Abb 17 Abb 22 Abb 19 a Abb 23 8 6 Abb 20 ...
Страница 6: ...5 Abb 29 Abb 30 Abb 26 b Abb 27 Abb 25 Abb 28 A Abb 24 Abb 26 a 0 6 0 7mm Abb 31 Abb 32 ...
