Impco ITK-1 Скачать руководство пользователя страница 12

 

April, 2008                                                     IMPCO Technologies Inc.                                            PPI-109-REV. B 
Page 12 of 12                                                      3030 South Susan St. 

Santa Ana, CA 92704 

www.impcotechnologies.com

 

 
 
 
 

WARNING: 

IMPROPER INSTALLATION OR USE OF THIS PRODUCT MAY CAUSE 

SERIOUS INJURY AND/OR PROPERTY DAMAGE. 

 
 

SERVICE TECHNICIANS AND USERS 

SHOULD CAREFULLY READ AND ABIDE BY THE PROVISIONS SET FORTH IN NATIONAL FIRE PROTECTION 
ASSOCIATION PAMPHLET #37 FOR STATIONARY ENGINES, #52 FOR CNG VEHICULAR FUEL SYSTEMS OR #58 FOR 
LPG SYSTEMS. 
 

INSTALLERS 

LPG INSTALLATIONS IN THE UNITED STATES MUST BE DONE IN ACCORDANCE WITH FEDERAL STATE OR LOCAL 
LAW, WHICHEVER IS APPLICABLE AND NATIONAL FIRE PROTECTION ASSOCIATION PAMPHLET #58, STANDARD 
FOR STORAGE AND HANDLING OF LIQUEFIED PETROLEUM GASES TO THE EXTENT THESE STANDARDS ARE NOT 
IN VIOLATION WITH FEDERAL, STATE OR LOCAL LAW. 
 

IN CANADA

 

REFER TO CAN/CGA PROPANE INSTALLATION CODES. 
 

CNG INSTALLATIONS IN THE UNITED STATES

 

MUST RE DONE IN ACCORDANCE WITH FEDERAL STATE OR LOCAL LAW AND NATIONAL FIRE PROTECTION 
ASSOCIATION PAMPHLET #52, COMPRESSED NATURAL GAS (CNG) VEHICULAR FUEL SYSTEMS TO THE EXTENT 
THESE STANDARDS ARE NOT IN VIOLATION WITH FEDERAL, STATE OR LOCAL LAW. 
 

IN CANADA

 

REFER TO CAN/CGA CNG INSTALLATION CODES. 
 

LPG AND/OR NATURAL GAS INSTALLATIONS ON STATIONARY ENGINES 

MUST RE DONE IN ACCORDANCE WITH FEDERAL, STATE OR LOCAL LAW AND NATIONAL FIRE PROTECTION 
ASSOCIATION PAMPHLET #37, STATIONARY COMBUSTION ENGINES AND GAS TURBINE ENGINES, TO THE EXTENT 
THESE STANDARDS ARE NOT IN VIOLATION WITH FEDERAL, STATE OR LOCAL LAW. FAILURE TO ABIDE BY THE 
ABOVE WILL VOID ANY IMPCO WARRANTY ON THE PRODUCTS AND MAY CAUSE SERIES INJURY OR PROPERTY 
DAMAGE. 
 
DUE TO THE INHERENT DANGER OF GASEOUS FUELS THE IMPCO PRODUCTS SHOULD NOT BE INSTALLED OR 
USED BY PERSONS NOT KNOWLEDGEABLE OF THE HAZARDS ASSOCIATED WITH THE USE OF GASEOUS FUELS.

 

 

Содержание ITK-1













Отзывы: