ImmersionRC vortex 250 pro Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 65

background image

Appendix B: The Wizard - What else does it setup?

On startup the wizard will reset Cleanflight configuration to its default state.

Once completed the following features, configurations and mode will be injected in
Cleanflight so you can start to enjoy your Vortex straight off the box with zero additional
configuration needed:

Flight Controller

Failsafe

Enabled, Throttle set to 1100

OneShot125

Feature Enabled

Rx Mode

PPM Sum Mode (all channels down a single cable)

Minimum Throttle

1100us

Maximum Throttle

1900us

Minimum Command

1015us

Angle mode on Aux1

1300 - 1700us

Horiz mode on Aux1

900 - 1300us

Acro mode on Aux1

1700 - 2100us

Channel Mapping

According to Wizard prompts

Accelerometer

Calibrated at wizard end

Pro-Tuning

Default ImmersionRC settings (based on UmmaGawd’s tune)

NOTE: If you have ‘tweaked’ any Cleanflight settings outside of the Vortex OSD, please
remember to back them up before running the wizard the next time, since it will reset
them to default settings.

50

«
...
48
49
50
51
52
...
»

Содержание vortex 250 pro


































































Отзывы:

Нет отзывов

Похожие инструкции для vortex 250 pro

Бренд: Ummagawd Страницы: 4

Бренд: XAG Страницы: 49

Бренд: Holy Stone Страницы: 30

TQ Performance Drone RtF

Бренд: Reely Страницы: 32

Бренд: udir/c Страницы: 10

Бренд: DELTA-SPORT Страницы: 126

LA VEHICLE land&air A90

Бренд: Marvelent Страницы: 21

Бренд: Kaiser Baas Страницы: 25

Бренд: Cocoon Страницы: 20

Бренд: sky viper Страницы: 5

Бренд: Brookstone Страницы: 25

Бренд: XciteRC Страницы: 36

Бренд: XciteRC Страницы: 48

Бренд: Arris Страницы: 15

Бренд: Arris Страницы: 18

Blade Inductrix Switch Air BNF

Бренд: Horizon Hobby Страницы: 19

Бренд: dji Страницы: 8

Бренд: dji Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды