Immersion RC Vortex 230 Mojo, Быстрый старт

Страница: 12 / 17

NOTE:​ ​To​ ​restart​ ​the​ ​wizard​ ​at
anytime,​ ​power​ ​up​ ​the​ ​quad,​ ​press
and​ ​hold​ ​the​ ​button​ ​on​ ​the​ ​led
board​ ​until​ ​Vortex​ ​beeps​ ​2​ ​times
(first​ ​beep​ ​after​ ​~3​ ​seconds,
second​ ​beep​ ​after​ ​~5​ ​seconds).
Alternatively​ ​you​ ​can​ ​also​ ​reset
the​ ​Tx​ ​Wizard​ ​via​ ​OSD​ ​menu
Once​ ​the​ ​wizard​ ​is​ ​finished,
various​ ​Betaflight​ ​settings​ ​will​ ​be
configured,​ ​including​ ​enabling
oneshot125,​ ​motor_stop,​ ​and
failsafe.
Another​ ​setting​ ​which​ ​is​ ​automatically​ ​made​ ​is​ ​the​ ​assignment​ ​of​ ​CH5​ ​to​ ​the​ ​flight​ ​mode,​ ​Acro,​ ​Horiz,​ ​and
Angle.​ ​To​ ​complete​ ​the​ ​setup,​ ​configure​ ​your​ ​R/C​ ​Tx​ ​to​ ​link​ ​CH5​ ​to​ ​a​ ​3-position​ ​switch.
Ensure​ ​that​ ​the​ ​switch​ ​correctly​ ​switches​ ​between​ ​the​ ​three​ ​flight​ ​modes,​ ​reflected​ ​in​ ​the​ ​top-right​ ​corner​ ​of
the​ ​OSD​ ​main​ ​landscape​ ​.
Note​ ​that​ ​It​ ​is​ ​highly​ ​recommended​ ​to​ ​attempt​ ​the​ ​maiden​ ​flight​ ​in​ ​either​ ​​Angle​,​ ​or​ ​​Horiz​ ​​mode.​ ​​Acro​ ​​takes
a​ ​little​ ​getting​ ​used​ ​to​ ​for​ ​those​ ​new​ ​to​ ​flying​ ​mini-quads.
NOTE:​ ​Even​ ​though​ ​the​ ​flight​ ​controller​ ​failsafe​ ​has​ ​been​ ​set​ ​by​ ​the​ ​wizard,​ ​it​ ​is​ ​important​ ​to​ ​also​ ​set
the​ ​R/C​ ​Rx​ ​failsafe.
Flyaways​ ​with​ ​mini-quads​ ​are​ ​almost​ ​always​ ​caused​ ​by​ ​incorrect​ ​failsafe​ ​settings!
NOTE:​ ​It​ ​is​ ​highly​ ​recommended​ ​to​ ​start​ ​the​ ​wizard​ ​with​ ​a​ ​‘new’​ ​profile​ ​in​ ​the​ ​R/C​ ​radio,​ ​without​ ​any
channel​ ​reversing,​ ​and​ ​also​ ​without​ ​any​ ​expo.​ ​Expo​ ​is​ ​all​ ​handled​ ​within​ ​the​ ​Pro-Tuning​ ​profiles.
12