background image

18

INS

TALL

AT

O

R

US

ER

MAINTEN

AN

CE TECHNI

CI

AN

1.19 FLUES, CHIMNEYS, CHIMNEY CAPS 

AND TERMINALS.

The flues, chimneys and chimney caps for the 

evacuation of combustion products must be in 

compliance with standards in force. The chimney 

caps and the roof exhaust terminals must respect 

the outlet quotas and the distance of the foreseen 

technical volumes from the current technical 

regulations.

Positioning the wall exhaust terminals.

 The 

exhaust terminals must:
- be installed on external perimeter walls of the 

building;

- be positioned according to the minimum 

distances specified in current technical 

standards.

Combustion products exhaust of natural or 

fan assisted appliances in open-top closed 

environments.

 In spaces closed on all sides 

with open tops (ventilation pits, air shafts, 

courtyards etc.), direct flue exhaust is allowed 

for conventional or fan assisted draught gas 

appliances with a heating power range from 4 to 

35 kW, provided the conditions as per the current 

technical standards are respected.

1.20 SYSTEM FILLING.

Once the boiler is connected, proceed with 

system filling via the filling valve (Fig. 1-32 and 

2-2). Filling is performed at low speed to ensure 

release of air bubbles in the water via the boiler 

and heating system vents.

The boiler has a built-in automatic venting valve 

on the circulator. 

Check if the cap is loose.

 Open the 

radiator air vent valves.

Close radiator vent valves when only water 

escapes from them.

Close the filling valve when the boiler manometer 

indicates approx. 1.2 bar. 

N.B.:

 during these operations start/up the 

circulation pump at intervals, acting on the main 

switch positioned on the control panel. 

Vent the 

circulation pump by loosening the front cap and 

keeping the motor running.

 Re-tighten the cap 

after the operation.

1.21 FILLING THE CONDENSATE TRAP.

On first lighting of the boiler combustion 

products may come out the condensate drain; 

after a few minutes’ operation check that this no 

longer occurs. This means that the trap is filled 

with condensate to the correct level preventing 

the passage of combustion products.

1.22 GAS SYSTEM START-UP.

To start up the system, refer to the current 

regulations. This divides the systems and 

therefore the start-up operations into three 

categories: new systems, modified systems, re-

activated systems.

In particular, for new gas systems:

- open windows and doors;
- avoid presence of sparks or naked flames;
- bleed all air from pipelines;
-  check that the internal system is properly sealed 

according to specifications.

1.23 BOILER START UP (IGNITION).

For issue of the Declaration of Conformity 

provided for by Italian Law, the following must 

be performed for boiler start-up:

-  check that the internal system is properly sealed 

according to specifications;

-  ensure that the type of gas used corresponds to 

boiler settings;

-  switch the boiler on and ensure correct ignition;
- make sure that the gas flow rate and relevant 

pressure values comply with those given in the 

manual ( Par. 3.18);

- ensure that the safety device is engaged in the 

event of gas supply failure and check activation 

time;

- check activation of the main switch located 

upstream from the boiler and in the boiler;

- check that the concentric intake-exhaust 

terminal (if fitted) is not blocked.

The boiler must not be started up even if only 

one of the checks should be negative.

N.B.:

 the boiler preliminary check must be carried 

out by a qualified technician. The boiler warranty 

is valid as of the date of testing.

The test certificate and warranty is issued to the 

user.

Содержание VICTRIX X12-242I









































Отзывы: