background image

28

INS

TALLER

US

ER

MAINTEN

AN

CE TECHNI

CI

AN

3.6   PUMP ANTI-LOCK FUNCTION

The hydronic module has a function that starts 

up the pump at least once every 24 hours for 30 

seconds in order to reduce the risk of the pump 

locking up due to prolonged inactivity.

3.7   3-WAY ANTI-LOCK FUNCTION

Both in "DHW" and in "DHW-system central 

heating" mode, the hydronic module has a func-

tion that activates the motorised 3-way unit 24 

hours after the last time it operated by running 

a complete cycle in order to reduce the risk of 

the 3-way locking up due to prolonged inactivity.

3.8   RADIATOR ANTIFREEZE 

FUNCTION.

If the system return water is below 4°C, the 

hydronic module starts up until it reaches 42°C.

3.9   SOLAR FUNCTION.

If the solar inlet is active, any accumulated DHW 

is heated to 50°C.

3.10 OUTDOOR UNIT DISABLE 

FUNCTION.

With the inlet active, outdoor unit operation is 

inhibited.

3.11 DIVERTER VALVE MANAGEMENT 

(SUMMER / WINTER).

The unit electronics has a 230V outlet to manage 

the summer / winter diverter valves. The switch 

occurs when the mode (summer / winter) is 

changed from the control panel or from the 

CAR

V2

.

3.12 ANTI-LEGIONALLA FUNCTION.

With the integrated DHW resistance, the func-

tion can be activated using the CAR

V2

.

See the instructions booklet to configure the 

function.

3.13 AUTOMATIC VENT FUNCTION.

In the case of new central heating systems and 

in particular mode for floor systems, it is very 

important that dearation is performed correctly. 

The function consists of the cyclic activation of 

the pump (100 s ON, 20 s OFF) and the 3-way 

valve (120 s D.H.W., 120 s C.H.). 

The function is activated in two different ways:
-  each time the hydronic module is re-powered;
- by pressing the buttons at the same time (3 

and 5 Fig. 2-1) for 5 seconds with the hydronic 

module in stand-by.

  

N.B.:

 if the hydronic module is connected to 

the CAR

V2

, the "stand-by" function can only be 

enabled from the remote control panel.

In the first case, the function has a duration of 

8 minutes and it can be interrupted by pressing 

the “reset” button (2). In the second case, it has 

a duration of 18 hours and it can be interrupted 

simply by switching the hydronic module on.
Activation of the function is signalled by the 

countdown shown on the indicator (14).

3.14 YEARLY APPLIANCE CHECK AND 

MAINTENANCE.

The following checks and maintenance should 

be performed at least once a year.

- Visually check for water leaks or oxidation 

from/on connections.

-  After discharging system pressure and bringing 

it to zero (read on the hydronic module pres-

sure gauge), make sure the expansion vessel 

pressure is at 1.0 bar.

- Check that the system static pressure (with 

system cold and after refilling the system by 

means of the filling cock) is between 1 and 1.2 

bar.

- Visually check that the safety and control 

devices have not been tampered with and/or 

short-circuited.

- Check the condition and integrity of the elec-

trical system and in particular:

  - supply voltage cables must be inside the 

fairleads;

  - there must be no traces of blackening or 

burning.

- Check ignition and operation.
- Check the operation of the appliance control 

and adjustment devices and in particular:

  - system regulation probes intervention;

IMPORTANT NOTE:

 in addition to yearly 

maintenance, you must also check the heating 

system and energy efficiency, with the frequency 

and procedures that comply with the technical 

regulations in force.

Содержание MAGIS PRO ERP

























































Отзывы: