Immergas Hercules Condensing 26 2 E Скачать руководство пользователя страница 69

Страница: 69 / 72

STHCkW ed 04/09

HERCULES Condensing Export

Technical Documentation

ERROR 31

Loss of remote control communication

The Remote Control is connected correctly.

N.B.: it is possible to use only remote controls supplied by Immergas

(CAR or Super CAR).

Check the connection between P.C.B. (clamps 42-43) and remote control

(IN+ and IN-) carried out respecting the polarity and using a dedicated

line to prevent interference.

Yes

Replace the remote control. If the anomaly persists, replace the P.C.B.

ERROR 32

Low temperature zone 2 flow probe anomaly

The wiring between the flow probe and the zones digital control

unit (connector X9 terminals 1-2) is OK.

Restore the electric connection/replace the wiring.

Yes

Replace L.T. zone 2 flow NTC probe. If the anomaly persists, replace the zones digital control unit.

ERROR 33

Low temperature zone 3 flow probe anomaly

The wiring between the flow probe and the zones digital control

unit (connector X13 terminals 1-2) is OK.

Restore the electric connection/replace the wiring.

Yes

Replace L.T. zone 3 flow NTC probe. If the anomaly persists, replace the zones digital control unit.

ERROR 34

Low temp. zone 2 overheating safety thermostat intervention.

The wiring between L.T. zone 2 safety thermostat and the zones

digital control unit (connector X12 terminals 3-4) is OK.

Restore the electric connection/replace the wiring.

Yes

Check/replace the L.T. zone 2 safety thermostat. If the anomaly persists, replace the zones digital control unit.

The L.T. zone 2 safety thermostat functions regularly (intervention

temperature higher than 55 °C).

Replace the over-heating safety thermostat.

Yes

The zone pump and the mixing valve function correctly.

See section G

Yes

Any CH system zone valve or cut-off cocks are open.

Restore circulation in the CH system by acting on the closed devices

and also check:

- the correct functioning of the zone by-pass;

- the opening times of any zone valve (on requirement it is possible to delay

ignition of the burner by acting on the boiler TIMER RT parameter);

- the correct functioning of any thermostatic valves.

Yes

The L.T. zone 2 NTC flow probe is OK (10 kΩ at 25°C).

Replace NTC probe.

Yes

Replace the zones digital control unit.

ERROR 35

Low temp. zone 3 overheating safety thermostat intervention.

The wiring between L.T. zone 3 safety thermostat and the zones

digital control unit (connector X13 terminals 3-4) is OK.

Restore the electric connection/replace the wiring.

Yes

Check/replace the L.T. zone 2 safety thermostat. If the anomaly persists, replace the zones digital control unit.

Содержание Hercules Condensing 26 2 E









































































Результаты поиска

Содержание Hercules Condensing 26 2 E

Отзывы:

Похожие инструкции для Hercules Condensing 26 2 E

Бренды по названию

Популярные бренды

Immergas Hercules Condensing 26 2 E, Руководство пользователя

Результаты поиска

Содержание Hercules Condensing 26 2 E

Отзывы:

Похожие инструкции для Hercules Condensing 26 2 E

Бренды по названию

Популярные бренды