Immergas Hercules Condensing 26 2 E Скачать руководство пользователя страница 31

Страница: 31 / 72

STHCkW ed 04/09

HERCULES Condensing Export

Technical Documentation

Air-gas adjustments.

The calibration of the total premix combustion system, when

necessary envisions the adjustment of the nominal heat output

and the air-gas ratio (off-set).
The two operations are only normally requested after a gas

transformation, after extraordinary maintenance (replacement

of a component of the air-gas circuit, replacement of the integrated

P.C.B. etc.) or when the appliance is not calibrated.

N.B.: The nominal output must also be adjusted during

the initial check.

Adjustment of nominal and minimum heat output.

The availability of maximum output is linked to the length of

the intake and exhaust pipes which, increasing, slightly reduces

the amount (flow rate) of inlet air and consequently also la

pressure of the burnt gas.

The boiler is calibrated as per standard for functioning with

a Ø60/100 horizontal concentric kit with length of 1m and

therefore the use of the flue kit with greater head losses requires

a check and possible adjustment of the nominal output accord-

ing to the table give below.

Below find the default settings present on the boiler (length

1 m):

HERCULES Condensing 26 2 E

MIN. MAX.

G20:

5060 (rpm)

GPL:

4400 (rpm)

MIN SPEED

G20:

1240 (rpm)

GPL:

1440 (rpm)

MAX. TIMER

G20:

4700 (rpm)

GPL:

4100 (rpm)

MIN. TIMER

G20:

1240 (rpm)

GPL:

1140 (rpm)

HERCULES Condensing 32 2 I

MIN. MAX.

G20:

4700 (rpm)

GPL:

4200 (rpm)

MIN SPEED

G20:

1260 (rpm)

GPL:

1160 (rpm)

MAX. TIMER

G20:

4700 (rpm)

GPL:

4200 (rpm)

MIN. TIMER

G20:

1260 (rpm)

GPL:

1160 (rpm)

The operation must be performed as follows and with respect

to the values stated in the heat output adjustment table:

- connect a differential manometer to the pressure points

(positive point) and

(negative point) found in the upper

part of the sealed chamber (iin this way the pressure difference

at the ends of the Venturi pipes (P1-P2) is detected and a pres-

sure signal is measured that corresponds to the real flow rate of

the air-gas mixture at the burner).

- start the boiler in the chimney sweep phase by pressing

key "C" and then check maximum fan speed (with burner

ignited);

- after about 5 minutes check and, if necessary, modify the

maximum number of fan revs. in CH mode and in DHW

mode until a pressure value is obtained (P1-P2) correspond-

ing to the nominal output.

- to modify the maximum number of fan revs. enter the

"Configurations" menu and inside the “BOILER PAR."

item, modify the value of the "MAX SPEED" parameter as

stated in the heat output adjustment table, until the pressure

value (P1-P2) corresponding to the maximum heat output

is obtained.

- N.B.: for the 26 2 E version, the maximum number of revs.

in CH mode is lower than the absolute maximum speed.

- to modify the maximum number of fan revs. in CH mode,

enter the "Configurations" menu and inside the "BOILER

PAR." item modify the value of the "MAX CH" parameter

as stated in the heat output adjustment table, until a pressure

value is obtained (P1-P2) that corresponds to the maximum

output in CH mode.

Содержание Hercules Condensing 26 2 E









































































Результаты поиска

Содержание Hercules Condensing 26 2 E

Отзывы:

Похожие инструкции для Hercules Condensing 26 2 E

Бренды по названию

Популярные бренды

Immergas Hercules Condensing 26 2 E, Руководство пользователя

Результаты поиска

Содержание Hercules Condensing 26 2 E

Отзывы:

Похожие инструкции для Hercules Condensing 26 2 E

Бренды по названию

Популярные бренды