Immergas EOLO Mini Скачать руководство пользователя страница 28

Страница: 28 / 48

STEMkW Special ed 01/08

EOLO Mini kW Special

Technical Documentation

D.h.w. request.

When domestic water is drawn it causes the contact of the

d.h.w. flow switch (S4) to close and enables operation in the

d.h.w. mode.

Burner ignition follows in exactly the same way as it does for

the central heating phase.

During the first few seconds after the gas valve (Y1) has been

powered, the current to the modulating coil (Y2) is limited to

the predefined soft ignition current.

When the flame is detected, the signal to the modulating coil

increases so as to immediately reach (if requested) the maximum

power set on the gas valve.

Flame modulation then occurs with reference to the diffe-

rence between the flow temperature coupled to the d.h.w.

temperature setting and the temperature measured by the

flow probe (B1).

When the reference temperature is reached, the burner is

kept working at minimum power and switched off when the

limit temperature of 85°C is reached (factory set with a fixed

set-point).

By way of the “D.h.w. thermostat” parameter it is possible to

establish that when the set value (+8 °C) is exceeded the contact

of the K1 relay opens, reclosing as soon as the temperature

drops (+6.5 °C) (correlated d.h.w. set -point).

Antifreeze request.

When the temperature measured by the heating flow probe

(B1) drops below 4°C, the P.C.B. enables ignition and keeps

the boiler working with the burner at minimum central heating

power until a boiler temperature of 42°C is reached (radiator

antifreeze).

The anti-freeze function is not enabled if the boiler main switch

is on (Stand-by).

“Chimneysweep” request.

By turning the main switch (R10) round to Reset for 8 to 15

seconds, upon its release the P.C.B. enables boiler ignition

and keeps it working at the maximum central heating power

set for 15 minutes.

During this time only the limit thermostat function is observed

(90°C) which is carried out by means of the central heating

flow probe (B1).

The function is indicated by the simultaneous flashing of

LEDs (2) and (3) and by the code “E07” on the CAR display

(if installed), it cannot be started if there is an ongoing d.h.w.

request.

It can be interrupted by cutting power to the circuit, putting

the main switch on (Stand-by) or after the 15 minutes.

* see Integrated P.C.B. programming.

Содержание EOLO Mini

















































Результаты поиска

Содержание EOLO Mini

Отзывы:

Похожие инструкции для EOLO Mini

Бренды по названию

Популярные бренды

Immergas EOLO Mini, Руководство пользователя

Результаты поиска

Содержание EOLO Mini

Отзывы:

Похожие инструкции для EOLO Mini

Бренды по названию

Популярные бренды