Gripper
Throat Depth
Inch (mm)
Flange Height
Inch (mm)
Working Pressure
Double Sided Grip
Force Up To
Actuation Time
PGS10C
.76 19.3
1.27 (32.3)
60 psi (413kPa) Min. –
100 psi (689 kPa) Max.
450lbs (200kgf) @ 80
psi (551kPa)
.050±.010 sec close /
<.090 sec open
PGS10D
.76 19.3
1.27 (32.3)
60 psi (413kPa) Min. –
100 psi (689 kPa) Max.
450lbs (200kgf) @ 80
psi (551kPa)
.050±.010 sec close /
<.090 sec open
PGS10E
.76 19.3
1.27 (32.3)
60 psi (413kPa) Min. –
100 psi (689 kPa) Max.
450lbs (200kgf) @ 80
psi (551kPa))
.050±.010 sec close /
<.090 sec open
PGS10F
.92 23.4
1.21 (30.6mm)
60 psi (413kPa) Min. –
100 psi (689 kPa) Max.
450lbs (200kgf) @ 80
psi (551kPa)
.050±.010 sec close /
<.090 sec open
PGS10R
.75 19
1.03 (26.3mm)
60 psi (413kPa) Min. –
100 psi (689 kPa) Max.
450lbs (200kgf) @ 80
psi (551kPa)
.050±.010 sec close /
<.090 sec open
PGS10S
.76 19.3
1.27 (32.3)
60 psi (413kPa) Min. –
100 psi (689 kPa) Max.
450lbs (200kgf) @ 80
psi (551kPa)
050±.010 sec close /
<.090 sec open
PGS10T
.76 19.3
1.27 (32.3)
60 psi (413kPa) Min. –
100 psi (689 kPa) Max.
450lbs (200kgf) @ 80
psi (551kPa)
.050±.010 sec close /
<.090 sec open
PGS10U
.76 19.3
1.27 (32.3)
60 psi (413kPa) Min. –
100 psi (689 kPa) Max.
450lbs (200kgf) @ 80
psi (551kPa)
.050±.010 sec close /
<.090 sec open
PGS10V
.76 19.3
1.27 (32.3)
60 psi (413kPa) Min. –
100 psi (689 kPa) Max.
450lbs (200kgf) @ 80
psi (551kPa)
.050±.010 sec close /
<.090 sec open
PGS10W
.76 19.3
1.27 (32.3)
60 psi (413kPa) Min. –
100 psi (689 kPa) Max.
450lbs (200kgf) @ 80
psi (551kPa)
.050±.010 sec close /
<.090 sec open
PGS10Y
.76 19.3
1.27 (32.3)
60 psi (413kPa) Min. –
100 psi (689 kPa) Max.
450lbs (200kgf) @ 80
psi (551kPa)
.050±.010 sec close /
<.090 sec open
VIII. Cleaning and Maintenance:
A) Remove excess grease from outer surfaces of gripper.
B) No required maintenance.
IX. Quality Assurance Requirements:
A) Verify that jaws shall open freely. Look for any irregular movement,
binding, or interference.
X. Specifications:
Our policy is one of continued research and development. We therefore reserve the right to amend,
without notice, the specifications given in this document. © 2015 Norgren Automation Solutions, LLC.
10
10/15
P/N 00537UI REV: 004
3. Apply Red Loctite 262 or equivalent to sensor stud, place thru jaw and tighten sensor
nut to
72in-lb
.
Cable should follow
the contour of the
gripper jaw
Cable storage loop
can be adjusted with
a push/pull motion to
provide more or less
cable slack in gripper
jaw area
User Instruction for PGS10 Series Gripper
