5.2 Crossfading between two channels
The crossfader (14) allows crossfading between chan-
nel 2 (preassigned) and channel 3 or channel 4 [to be
selected via the button C.F. ASSIGN (15)].
1) Use the button C.F. ASSIGN (15) to select either
channel 3 or channel 4 for crossfading:
button not pressed:
channel 3
button pressed:
channel 4
2) Control the channel selected and channel 2 to an
optimum level (see chapter 5.1 “Basic adjustment
of the input channels”).
3) If desired, suppress the stereo audio sources at the
other two channels: switch them off, set them to
pause, or completely close their channel faders.
4) Now crossfading between the two channels is pos-
sible:
To fade in channel 2/fade out channel 3 or 4,
slide the crossfader to the left.
To fade in channel 3 or 4/fade out channel 2,
slide the crossfader to the right.
With the crossfader in mid-position, both chan-
nels are simultaneously fed to the outputs.
5) Via the VU-meter (3), adjust the desired level for
the master output AMP (19) with the master control
(1).
Usually an optimum level control is obtained if
the VU-meter shows values in the 0 dB range at
high volume. However, if the output level is too high
or too low for the following unit, control the master
signal accordingly to a lower or higher level.
5.3 Mixing the audio sources connected
1) Slide the crossfader (14) to mid-position.
2) Use the faders (12) of the input channels to adjust
the desired volume ratio of the audio sources:
Adjust the audio sources to be heard at the highest
volume to an optimum level (see chapter 5.1) and
reduce the levels of the other audio sources ac-
cordingly.
If a channel is not used, its level control should
be set to minimum.
3) Via the VU-meter (3), adjust the level of the master
signal with the master control (1) [see chapter 5.2,
position 5].
5.4 Announcements via the DJ microphone
To switch on or off the DJ microphone at channel 1 and
to activate the talkover feature, set the selector switch
MIC (13) to the corresponding position:
1. With the switch set to the left (“OFF”), the micro-
phone is switched off.
2. In mid-position (“ON”), the microphone is switched
on (LED above the switch lights up).
3. With the switch set to the right (“TALKOVER”), the
microphone is switched on and the talkover feature
is activated (LED above the switch lights up): During
a microphone announcement, the levels of chan-
nels 2 to 4 are automatically attenuated by 16 dB.
5.5 Pre-fader listening to the channels
The PFL feature (pre-fader listening = monitoring a
channel ahead of the channel fader) allows to monitor
each of the input channels 1 to 4 via headphones
connected to the jack PHONES (10) even if the corre-
sponding channel is faded out. Thus, it is possible,
e. g. to select the desired title on a CD or to time the
moment for fading in an audio source.
1) For pre-fader listening to a channel, press the cor-
responding PFL switch (11); the LED above it will
light up.
2) Adjust the desired headphone volume with the con-
trol PFL LEVEL (4).
6
Specifications
Inputs
Mic, mono: . . . . . . . . . . . . . 1.5 mV
Phono, stereo: . . . . . . . . . . 3 mV
Line, stereo: . . . . . . . . . . . . 150 mV
Outputs
Master, stereo: . . . . . . . . . . 1 V/600
Ω
Rec, stereo: . . . . . . . . . . . . 0.5 V/600
Ω
Headphones, stereo: . . . . .
≥
8
Ω
General information
Frequency range: . . . . . . . . 20 – 20 000 Hz
THD: . . . . . . . . . . . . . . . . . . 0.1 %
S/N ratio: . . . . . . . . . . . . . . 61 dB, unweighted
Equalizer
low frequencies: . . . . . . . +12 dB, -26 dB/50 Hz
midrange frequencies: . . +12 dB, -26 dB/1 kHz
high frequencies: . . . . . . +12 dB, -26 dB/10 kHz
Talkover: . . . . . . . . . . . . . . . -16 dB
Power supply: . . . . . . . . . . . 12 V~/1 A via supplied
power supply unit con-
nected to 230 V~/50 Hz
Ambient temperature: . . . . . 0 – 40 °C
Dimensions: . . . . . . . . . . . . 280 x 266 x 105 mm
Weight: . . . . . . . . . . . . . . . . 2.1 kg
According to the manufacturer.
Subject to technical change.
GB
9
All rights reserved by MONACOR
®
INTERNATIONAL GmbH & Co. KG. No part of this instruction manual may
be reproduced in any form or by any means for any commercial use.
