background image

6.2 Recharging Batteries 

A low battery warning light is emitted from the On/Off 
light (e) approximately four hours before recharge. 
         DO NOT OVER CHARGE BATTERIES! 
      DO NOT CHARGE ALKALINE BATTERIES! 
Plug the charger provided into the recharging point on the 
instrument, located immediately below the control panel. 
The charger plugs into a standard 240V outlet. 

 

6.3 Battery Charging Time 
Standard full Charge time is approximately 7 hours. 
However the instrument can be charged and used 
simultaneously. In some instances a car charger 
accessory kit is an advantage. 

 

7. Checking Accuracy  

Your Imex instrument has been pre-set and calibrated for 
accuracy before dispatch and should perform within the 
stated accuracy tolerance in standard conditions. However 
if the instrument is knocked, poorly transported or 
mistreated in any way the accuracy may be compromised 
and unit may need re-calibration. 
 
On commencement of a task it is advisable to carry out a 
simple control check. 

 

7.1 Level Checking – Horizontal 

Place instrument approximately 30m from a blank wall 
and with X1 axis square to the wall project a line onto the 
wall and mark line with a fine pencil or similar. 
 
Turn the instrument 180º to X2 and repeat  

Содержание 77R





















Отзывы: