TRADUCTION OF THE ORIGINAL INSTRUCTIONS FOR USE
BS 300/60 AFI-E ED.2010 rev.00
21/61
*HIGHEST SAWFRAME POSITION
* SET BY THE MANUFACTURER
, corresponds to the highest point the
sawframe can reach,
2- *START OF THE CUT automatic thanks to the position sensor
–1/RI0460-.
3- *END OF THE CUT chosen by the user, by moving up or down the small rod which activates the
correspondent end-stroke
–4/RI0460-.
4- *LOWEST SAWFRAME POSITION*
SET BY THE MANUFACTURER,
corresponds to the lowest point the
sawframe can reach
Usually the positions 1 and 4
– set by the manufacturer – correspond to 100% of the maximum
cutting capacity allowed. In case of variations please contact the Technical Service.
OPEN VICE (18):
push it to open the machine vice. The led light on indicates that the command has been set
( ex. when the cycle starts by open vice, the vice will open again at the end of the working cycle).
For automatic machine only, if you press it within the TEST button -pos.4/dr.RI0055- it open the feeder vice
CLOSE VICE (19):
push it to close the machine vice. The same as for the open vice (see above).
For automatic machine only, if you press it within the TEST button -pos.4/dr.RI0055- it close the feeder vice
CYCLE START(20):
it allows to start a semiautomatic cutting cycle (when the led light of the function F3 is
not flashing - pos. 25 / dr. RI0055).
On request we can also programme the machine so that this button is not operative (for ex. by
connecting the command to the pedal), in order to avoid unwanted startings (ask it to Service
Assistance).
The corresponding led light indicates that the machine is working.
CYCLE STOP (21):
it allows to stop the semiautomatic or automatic cutting cycle in each moment and to
push other buttons of the manual commands.
FUNCTION 1 = F1 (26):
If the led light is on, the returning stroke can be done with the tool in movement; if it
is off with the tool stopped.
FUNCTION 2 = F2
(27):
it allows only the slow cutting stroke, if the led light is on (short cycle); it allows the
appro slow cutting stroke if the led light is off (normal cycle).
FUNCTION 3 = F3 (25):
if led light is on, it stops the semiautomatic cutting cycle on the returning point (at the
end of the cut).
TOOL SPEED -1
(11):
by pushing this button when the machine is not working you can pre-select the lowest
cutting speed (only for 2 speed machines
); if pushed when the tool is in movement there is a speed
decrease (only in machines with ESC).
If the led is on, it means that the preselection has been made.
TOOL SPEED 0
(12): by pushing it when the machine is not working you can pre-select cutting speed 0. For
safety the function is not operative when machine is working. The led light on indicates that pre-selection has
been made.
TOOL SPEED+2 (13):
by pushing it when the machine is not working you can pre-select the highest speed
(only for 2 speed machines);
if pushed when the tool is moving, it determins a speed increase (only in
machines equipped with inverter = ESC).
The led light on indicates that pre-selection has been made.
COOLANT ON IN SEMIAUTOMATIC CYCLE (24
): by led light on the coolant pump is operative only in the
semiautomatic cutting cycle.
It is better if the working cycle time is longer than 15 seconds.
COOLANT ON (23
): by led light on, the coolant pump is always operative.
Содержание BS300/60 AFI-E
