Ikra IEVL 1532, Руководство по эксплуатации

Страница: 30 / 100

GB-10
GB | Operating Instructions
obtain the maximum cutting performance from your unit
and to reduce the risk of the trailing the extension lead
from entering the cutting path.
• Place the bulk of the supply cable on the lawn close to
the starting point (position 1, Fig. 13).
• Hold the handle assembly with both hands.
WARNING: Do not attempt to operate your Machine with
one hand - you must guide it with both hands. Do not
operate your machine on sanded, concrete or woodened
ground.
• Tilt the handle downwards to slightly raise the front of
your unit and to reduce the risk of lawn damage while
starting, depress the safety lock-off button (2a) on the
switchbox and while still depressed pull the switch le-
ver (2b) towards you. Your machine will start and you
can now allow the lock-off button (2a) to be released
and lower your Machine to its proper cutting position,
and commence cutting.
• Proceed down the cutting area as shown in Fig. 13,
working from position 1 towards position 2 and, on
reaching position 2, turn to the right and proceed to-
wards position 3. Always working away from the cable.
Do not adopt the method as shown in Fig. 14, working
towards the cable, as this is dangerous practice.
SETTING THE WORKING DEPTH
The working depth is adjustable to 4 heights referring to
below table. Pull adjustment arm (7) away from one posi-
tion and move to catch in desired position.
Position Scarifier Aerator
1 -12 mm -3 mm
2 -8 mm 1 mm
3 -4 mm 5 mm
4 4 mm 13 mm
11. MAINTENANCE
WARNING! Before carrying out any repairs or
servicing work, you must ensure that the prod-
uct has been disconnected from the power sup-
ply. Repairs and maintenance work other than
described within this instruction manual may be
performed only by qualified specialist!
Service and storage
To ensure long and reliable service, carry out the follow-
ing maintenance regularly. Servicing and cleaning work
on the product and the removal of the guards may only
be carried out after the motor has been switched off and
the plug disconnected from the power supply.
1. Regularly check for obvious defects such as loose,
dislodged or damaged chain and guide bar, loose fix -
ings and worn or damaged components.
2. Check that covers and guards are undamaged and
correctly fitted. Carry out necessary maintenance or
repairs before using the product.
3. If the cutting device should happen to fail despite the
care taken in manufacturing and testing, repair should
be carried out by an authorized specialist.
4. Do not clean the product while it is running.
5. Ensure that all the fastening elements (screws, nuts,
etc.) are tight at all times so that you can safely work
with the product.
6. Check the product frequently for signs of wear. Re-
place worn or damaged parts.
7. Store your product in a dry place. To ensure a long
service life all screw parts should be cleaned and then
oiled.
8. Clean the product with a brush or cloth. Do not use
any solvents or water to remove dirt.
9. The component that is subject to most wear is the
cutting device. You should therefore check the condi-
tion of the cutting device and its mounting at regular
intervals.
- If the cutting device is worn or blunt it must be re-
placed immediately;
- If the product starts to suffer from excessive vibra-
tions, this means that the cutting device has not
been balanced correctly or has suffered deforma-
tion due to impacts. In this case it must be repaired
or replaced.
After use
1. Switch the product off, disconnect it from the power
supply and let it cool down.
2. Check, clean and store the product as described be-
low.
3. Turn the adjusting knob (7) to the „HIGH“ position.
4. Loosen the fasteners (4) and (9), with which the han-
dle parts are locked in place. The handle can then
be folded down into a Z-shape to save storage space
(fig. 15).
Grass catcher
1. Inspect the grass catcher before each use. Do not
use it if you find any damage.
2. Clean the grass catcher after operation. Let the grass
catcher dry thoroughly before storing to avoid mildew.
Transportation
1. Switch the product off and disconnect it from power
supply before transporting it anywhere.
2. Turn the adjusting knob (7) to the „HIGH“ position.
3. Attach transportation guards, if applicable.
4. Always transport the product by its handle.
5. Protect the product from any heavy impact or strong
vibrations which may occur during transportation in
vehicles.
6. Secure the product to prevent it from slipping or fall-
ing over.