IKH XW029 Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 58

IKH XW029 Скачать руководство пользователя страница 47

47

10.

Slide the outer blade collar onto the saw spindle.

11.

Screw the arbor nut, with the low side facing the
blade, onto the saw spindle (left-handed thread).

-

When tightening, do not use extension arm to
avoid overtightening the arbor nut. Do not tap
the spanner with a hammer or similar during
tightening.

-

After tightening the arbor nut, do not forget to
remove the saw spindle lock bar.

-

Fix the saw blade to the spindle.

-

When the spindle diameter is less than the saw blade bore diameter, reduction sleeves should be
used to make up the difference. Make sure the reduction sleeves are of correct size. The use of
loose rings or bushes is not permitted.

12.

Loosen the screw (a) of the riving knife bracket.

13.

Adjust the distance between the saw blade’s outer edge and the riving knife (b). It must be 3-8
mm.

14.

Reinstall the throat plate and blade guard.

Slot for the saw blade in the table

The total width of the slot for the saw blade is 12 mm.

Selection of the saw blade and riving knife

-

Saw blade diameter:

254 mm

-

Saw blade thickness: 3 mm

The operator should only select saw blades of a diameter and thickness suitable for the machine, as
specified in this manual. Selection of the riving knife is dependent on the saw blade thickness and
saw blade diameter. The operator should ensure that the riving knife selected is suitable for the saw
blade being used. The riving knife-guiding slot should be no more than 0,5 mm wider than the riv-
ing knife guiding elements.

Working tips

-

Before cutting a workpiece to size, make trial cuts in scrap pieces.

-

Always place a workpiece on the saw table in such way that it cannot tilt or rock (e.g. place a
curved board on the table with the convex side up).

-

When working with long stock, use suitable supports such as table rear or side extensions.

-

Keep surfaces of the saw table and saw blade clean - in particular, remove resin residue with a
suitable cleaning and maintenance spray.

MAINTENANCE

-

Prior to all servicing

•

switch the machine off

•

unplug the power cable and

•

wait until the saw blade has come to a complete stop.

-

Check that all safety devices are operational after each service.

-

Replace defective parts, especially of safety devices, only with original replacement parts. Parts
not tested and approved by the machine manufacturer can cause unforeseen damage.

-

Repair and maintenance work other than described in this section shall only be carried out by a
qualified specialist.

c

a

b

3-8 mm

«
...
45
46
47
48
49
...
»

Содержание XW029



























































Отзывы:

Нет отзывов