Ikegami HLM-905WR, Руководство по эксплуатации

Страница: 28 / 80

- - 18
ԙ
Setting the function assignment of F2 switch
࡮
The function assignment is selectable in the same
way as that shown above
Ԙ
by pressing the
F2
switch on the front panel.
࡮
Default setting is VITC ON.
㩷
Ԛ
Setting the serial remote control ID number
࡮
Used to set the ID number (01 to 99) of the monitor.
* The ID number for exclusive use of the TSL sets it
in MENU13-5
࡮
The ID number is assigned to each monitor in
order to perform remote operation with the serial
remote controller.
* SRC-301A/Z is discontinuation.
࡮
Default setting is 01.
㩷
㩷
ԛ
Setting the ASPECT ratio to Automatic or Manual
x
AUTO:
When the SDTV signal is input, the ASPECT in-
formation that has been set up by using the
ASPECT
switch is individually stored in memory by
each input channel of VBS/SDI chA (for SD
only)/SDI chB (for SD only). (HD-SID signal is fixed
to 16:9.)
When the individual channel is switched over in
such a manner as “VBS
Ù
SDI chA
Ù
SDI chB,” the
ASPECT information that has been stored in
memory will automatically be set up.
࡮
MANUAL:
The information that has been set up by using the
ASPECT
switch will be set up to the same aspect
value without exception.
࡮
Default setting is AUTO.
* When switching the ASPECT in the parallel re-
mote mode, set the ASPECT ratio to “MANUAL”.
㩷
Ԝ
Setting the assignment of “CONT” manual control
࡮
Used to assign the function to the [CONT] control
(switch popped up).
࡮
CONT
㧦
contrast’s manual level setting
࡮
BL
㧦
backlight level setting .
࡮
Default setting is CONT.
̪
With setting at “BL”, the ““5-1
ԟ
” item automati-
cally varies accordingly. Also the preset data is
kept intact even when the switch is pressed.
㩷
ԝ
Setting the tally lamp indication
࡮
Set any of the following display modes of the tally
lamps located at the top of the front of the moni-
tor.
࡮
R/G
㧦
R is on the left side and G on the right side,
when facing the screen.
[R-TALLY ON] [G-TALLY ON]
㩷
࡮
G/R
㧦
G is on the left side and R on the right side,
when facing the screen.
[G-TALLY ON] [R-TALLY ON]
࡮
R+G
㧦
The entire tally is displayed.
The lamp is displayed in amber when both the
R-TALLY and G-TALLY are set at ON. Both R-
and G-TALLY at ON.
㩷
φ=
R-TALLY ON]
φ
[G-TALLY ON]
φ
[Both R and G-TALLY at ON]
㩷
࡮
R/G ALL
㧦6JG
entire tally is displayed.
The lamp is displayed R/G when both the
R-TALLY and G-TALLY are set at ON. Both R-
and G-TALLY at ON.
㩷
φ=
R-TALLY ON]
φ
[G-TALLY ON]
φ
[Both R and G-TALLY at ON]
㩷
࡮
G/R ALL
㧦6JG
entire tally is displayed.
The lamp is displayed G/R when both the
R-TALLY and G-TALLY are set at ON. Both R-
and G-TALLY at ON.
㩷
φ=
R-TALLY ON]
φ
[G-TALLY ON]
φ
[Both R and G-TALLY at ON]
㩷
࡮
Default setting is R/G.
㩷
Ԟ
Setting the same-size (dot-by-dot) display
ON/OFF
࡮
Set to ON in order to reproduce the input signal in
its original pixels without enlargement or reduc-
tion.
࡮
This function can be assigned with the
F1 F2
switch on the front panel.
࡮
Default setting is OFF.
̪
Signals in 480i/575i format are not in square pix-
els. Therefore, the aspect ratio will be displayed
differently from the original image.
㩷
ԟ
Setting the same-size display area
࡮
Used to set the display area for the input of signals
in the 1080i/1080p format, which has more pixels
than those (1280x768) of the panel.
࡮
CENTER(Screen center displayed)
࡮
L/T(Screen top left displayed)
࡮
L/C(Screen center left displayed)
࡮
L/B(Screen bottom left displayed)
㪩
㪞
㪘㪤㪙㪜㪩
䌒㩷 㪞㩷
㪞 㪩
㪩
㪞
䌒 㪞
㪩
㪞
㪞 㪩