Ikegami HLM-3250W, Руководство по эксплуатации

Страница: 39 / 64

- 30 -
* The settings on MENU10 can be made only when the PC input is selected.
* When the computer screen resolution is set at WXGA, SXGA, UXGA and WUXGA, be sure to select the refresh
frequency of 60 Hz.
①
Sett i ng the d i splay mode w i th DVI i nput (PC format)
Used to preset the image display size in receiving
the PC-format DVI signals. This is effective when
a DVI input mode has been selected and the related
signal is detected.
• REAL : Images are displayed 1 : 1 with the
resolution of input signal.
• NORMAL : With the aspect ratio intact, images
are enlarged or reduced in this
panel’s maximum displayable size.
• FULL : Images are fully displayed onscreen
(1920 x 1080) for all input signals.
• Default setting is NORMAL.
◆
Display pixels with respect to PC input signals in each
mode
②
Sw i tch i ng between analog PC and COMPONENT
i nput s i gnals (Sett i ngs only for the CM-240)
PC : Analog PC input of the CM-240 is
selected.
VIDEO : COMPONENT input of the CM-240 is
selected.
This function can be assigned with the F1 F2 switch
on the front panel.
• Default setting is VIDEO.
③ Sett i ng the d i splay mode w i th analog PC i nput
(Sett i ngs only for the CM-240)
Used to preset the image display size. The table
below Item ① is also applicable with the display
pixel size with respect to the input signal mode.
• REAL : Images are displayed 1 : 1 with the
resolution of input signal.
• NORMAL : With the aspect ratio intact, images
are enlarged or reduced in this
panel’s maximum displayable size.
• FULL : Images are fully displayed onscreen
(1920 x 1080).
• Default setting is NORMAL.
4-13 . Descr i pt i on of MENU 10 Funct i ons
⑧ Adjusting the clock with analog PC input (Settings only for the CM-240)
⑤ Executing the automatic adjustment of PC input (Only for the DVI(PC) and CM-240)
Ｍ Ｅ Ｎ Ｕ １ ０（Ｐ Ｃ ＳＥＴ ＵＰ ）
Ｓ Ｅ Ｔ → Ｅ ＸＩ Ｔ→
ESC ENT
１ ．ＤＶＩ ＳＥ ＴＵＰ
２ ．→ＥＸ ＰＡＮ ＳＩＯＮ
ＮＯＲ ＭＡＬ
３ ．ＣＯＭ Ｐ Ｓ ＥＴＵＰ
４ ．→ＩＮ ＰＵＴ ＳＥＬ ＥＣＴ
ＶＩＤ ＥＯ
５ ．→ＥＸ ＰＡＮ ＳＩＯＮ ＮＯＲ ＭＡＬ
６ ．→ＸＧ Ａ／Ｗ ＸＧＡ ＸＧＡ
７ ．ＡＵＴ Ｏ Ａ ＤＪＵＳ Ｔ ＥＸＥ ＣＵＴ Ｅ
８ ．→Ｈ ＰＯＳ ＩＴＩＯ Ｎ ０
９ ．→Ｖ ＰＯＳ ＩＴＩＯ Ｎ ０
10． → ＣＬＯ ＣＫ ０
11． → ＰＨＡ ＳＥ ０
① Setting the display mode with DVI input (PC format)
③ Setting the display mode with analog PC input (Settings only for the CM-240)
④ Selecting the analog PC input XGA/WXGA (Settings only for the CM-240)
⑨ Adjusting the phase with analog PC input (Settings only for the CM-240)
⑦ Adjusting the vertical onscreen position with PC input (Only for the DVI(PC) and CM-240)
⑥ Adjusting the horizontal onscreen position with PC input (Only for the DVI(PC) and CM-240)
② Switching between analog PC and COMPONENT input signals (Settings only for the CM-240)
Pixel size and aspect ratio PC input signal
(pixels, aspect ratio)
REAL NORMAL FULL
VGA
(640 × 480 , 4:3) 640 × 480
(4:3)
1440×1080
(4:3)
1920×1080
(16:9)
SVGA
(800 × 600 , 4:3) 800 × 600
(4:3)
1440×1080
(4:3)
1920×1080
(16:9)
XGA
(1024 × 768 , 4:3) 1024×768
(4:3)
1440×1080
(4:3)
1920×1080
(16:9)
WXGA
(1280 × 768 , 15:9) 1280×768
(15:9)
1800×1080
(15:9)
1920×1080
(16:9)
SXGA
(1280 × 1024 , 5:4) 1280×1024
(5:4)
1350×1080
(5:4)
1920×1080
(16:9)
UXGA
(1600 × 1200 , 4:3) 1600×1080
(4:3)
1440×1080
(4:3)
1920×1080
(16:9)
WUX GA
(1920 × 1200 , 16:1 0) 1920×1080
(16:10)
1728×1080
(16:10)
1920×1080
(16:9)
<REAL display mode with UXGA signal>
Onscreen display area
(1080 pixels)
Input signal
(1200 pixels)
Onscreen display area
(1080 pixels)
Input signal
(1200 pixels)
Onscreen display area
(1920 pixels)
<REAL display mode with WUXGA signal>
*1:In the REAL display mode with UXGA/WUXGA
signals, the input signal’s number of vertical pixels
(1200 pixels) is greater than the display panel’s
number of corresponding pixels (1080 pixels). As
shown below, therefore, the 120-pixel images are
cut off on screen at the top and bottom.