IKEA UDDARP 205.237.67, Руководство пользователя, Страница: 9 / 28

9 ENGLISH
To download the full version visit www.ikea.com
What to do if...
The washing machine may sometimes not work properly for certain reasons. Before calling the After-sales service, it is recommended
to check to see if the problem can be easily resolved using the following list.
Problem Possible causes / Solutions:
The washing machine does not turn on. • The plug is not inserted into the electrical outlet, or not enough to make
contact.
• There has been a power failure.
The wash cycle does not start. • The “ON/OFF” button has not been pressed.
• The “Start/Pause” button has not been pressed.
• The water tap is not open.
• A “Start delay” has been set.
• The machine is in DEMO mode; check if the display shows “dOn”
• The door is not fully closed.
The washing machine does not fill with water
(the message “h2o” is shown on the display).
“Beep” sound every 5 seconds.
• The water intake hose is not connected to the tap.
• The hose is bent.
• The water tap is not open.
• The mains water supply has been shut off.
• There is not enough pressure.
• The “Start/Pause” button has not been pressed.
The washing machine loads and drains water
continuously.
• The drain hose has not been installed at 65 to 100 cm from the ground.
• The end of the drain hose is immersed in water.
• The drain connector on the wall does not have an air vent.
• If the problem persists after having performed these checks, close the water
tap, shut off the washing machine, and call the After-sales service. If the
dwelling is located on one of the uppermost floors of a building, a siphon
effect can sometimes occur, thus causing the washing machine to load and
drain water continuously. Special anti-siphon valves are available on the
market to prevent these types of problems.
The washing machine does not drain or does
not spin.
• The programme does not include the draining function: with certain
programmes it must be activated manually.
• The drain hose is bent.
• The drain line is obstructed.
The washing machine vibrates excessively
during the spin cycle.
• At the time of installation, the drum was not properly unblocked.
• The washing machine is not level.
• The washing machine is squeezed between furniture and the wall.
The washing machine leaks water • The water intake hose has not been tightened properly.
• The detergent dispenser is clogged.
• The drain hose has not been properly fastened.
The machine is locked and the display flashes,
indicating an error code (e.g. F-01, F-..).
• Shut off the machine, disconnect the plug from the outlet, and wait about 1
minute before turning it back on.
• If the problem persists, call the After-sales service.
Too much foam is formed. • The detergent is not compatible with the washing machine (it must bear the
wording “for washing machines”, “for hand washing and washing machines”,
or something similar).
• The dosage was excessive.
Door is locked, with or without failure
indication, and the programme does not run.
• Door is locked in case of power breakdown. Programme will continue
automatically as soon as the mains is available again.
• Washing machine is in a standstill. Programme will continue automatically
after the origin of the standstill does not persist anymore.
IKEA UDDARP 7
220-240
50
D 0,689 69 44 B 4 0,5 80 C
Brand Model
Rated
capacity
(kg)
Voltage (V)
Frequency
(Hz)
Energy
efficiency
class
Energy con-
sumption in
kWh per cycle,
based on the
eco 40-60
programme.
Weighted
energy
consumption
in kWh per
100 washing
cycles
Water con-
sumption
of the eco
programme
in liters per
cycle
Spin-drying
efficienty
class
Power consumption in Noise emis-
sions during
eco 40-60
programme
(spinning
phase)
dB(A)
Noise
Emission Class
delay start
(W)
standby
mode
(W)
Technical data