background image

15

Working with the unit

Refer to the operating instructions for the fi lling 
level of the medium and the immersion depth 
into the dispersing element used.

Caution: Burns hazard!

 If a dispersing element 

is not inserted into the drive fl ange as far as the 
mark it can become extremely hot in operation 
and thus suffer damage.

So as to avoid unintentional ingress of air into the 
medium due to excessively turbulent rotation, the 
whole unit can be placed a little off centre in the 
stirring vessel.

By using the turning knob (pos. 10) the speed may 
be infi nitely varied to meet the requirements of the 
medium to be processed.
The idle speed for the drive unit can be adjusted 
in the range 3 000 and 25 000 rpm; the value will 
be shown on the LED display.

If these conditions are met 
the unit is ready for service 
when the mains plug has 
been plugged in.

The driving unit is switched on by means of the 
On/Off- switch (pos. 9).

Also pay attention to the ambient conditions lis-
ted in the “Technical data”.

Assembling the dispersion tool
(Overview fi g. 5)

- Open the knurled screw (pos. 3) so that the th-

read does not protrude into the hole.

- Insert the dispersing element (pos. 2) from 

the bottom into the drive unit (pos. 1) as far 
as the stop. The shaft will audibly click into 
place when a small amount of force is ap-
plied (sprung ball bearing) - depending on 
the type of disperser. The dispersing element 
is fi tted correctly if the dispersing element is 
fl ush with the bottom edge of the drive unit.

Attention: 

Now secure the dispersing element 

by screwing the knurled screw tight (pos. 3).

Maintenance and cleaning

Fig. 5

0 mm

!

!

1

3

2

2

Spare parts order

When ordering spare parts, please give:
- Machine type
- Manufacturing number, see type plate
- Item and designation of the spare part,
  see 

www.ika.com

, spare parts diagram and 

spare parts list

Repair

In case of repair the device has to be cleaned and 
free from any materials which may constitute a 
health hazard.
For this use the "certifi cate of compliance" or 
download the form from the 

IKA

®

 website 

www.ika.com

.

If you require servicing, return the appliance in its 
original packaging.
Storage packaging is not suffi

  cient.  Please  also 

use suitable transport packaging.

The drive unit is maintenance-free but not immu-
ne from wear. The motor brushes and the coup-
ling wear out over time.

Cleaning

For cleaning disconnect the 
main plug.

To clean the drive use only water with a detergent 
that contains tensides, or use isopropylalcohol for 
stubborn soiling (not for plastic parts).

Dispersion tools:

 Consider please the manuals 

associated to the dispersion tools.

- Do not allow moisture to get into the appliance 

when cleaning.

- Wear protective gloves when cleaning the de-

vices.

- Please consult with 

IKA

®

 before using any 

cleaning or decontamination methods, other 
than those recommended here. 

Содержание ULTRA-TURRAX T 18 digital










Отзывы: