background image

32

   ›  The device is maintenance-free� It is only subject to the natural wear and tear of components 

and their statistical failure rate�

/// Cleaning:

   › For cleaning disconnect the mains plug!
  › Use only cleaning agents which have been approved by IKA to clean IKA devices�

These are water (with tenside) and isopropanol�

   › Wear protective gloves during cleaning the devices�
   › Electrical devices may not be placed in the cleansing agent for the purpose of cleaning�
   › Do not allow moisture to get into the device when cleaning�
   › Before using another than the recommended method for cleaning or decontamination, the

user must ascertain with IKA that this method does not destroy the device�

/// Spare parts order:

› When ordering spare parts, please give:

- device type�
- serial number, see type plate�
- software version (upon device starting up)�

/// Repair:

  Please only send devices in for repair that have been cleaned and are free of materials which

 

might present health hazards�
If your appliance requires repair, return it in its original packaging� Storage packaging is not

 

sufficient when sending the device - also use appropriate transport packaging�

Maintenance and cleaning

Содержание Plate RCT digital





































Отзывы: