background image

-4-

www.igmtools.com

Contents

1. Declaration of conformity

1.1 Warranty

2. About this manual

3. Fusion 3 Specifications

3.1 Contents

3.2 Technical

3.3 Main Features

4. General Safety

4.1 Intended Use

4.2 Work Area

4.3 Personal Safety

4.4 Tool Use

4.5 Guarding Related Warnings

4.6 Work Related Warnings

4.7 Kickback Causes and Related Warnings   

4.8  Table  Saw  Operating  Prodedure  Warnings                      

4.9 Electrical

4.10 Noise emissions

4.11 Grounding

4.12 Rulings

4.13 Notice on safe use of the machine 

5. Machine overview

5.1 Controls

6. Setup

6.1 Receiving and unpacking

6.2 Inventory

6.3 Loose parts & overview

6.4 General setup

6.5 Installing/removing the throat plate

6.6 Installing/removing safety accessories

6.7 Installing/removing the blade

7.

 

Adjustments

7.1 Fence adjustments

7.2 Table adjustments

7.3 Arbor and tilt adjustments

7.4 Accessory adjustments

7.5 Push block and push stick

8. Type of cut

8.1 Ripping

8.2 Bevel ripping

8.3 Ripping small workpieces

8.4 Cross cutting

8.5 Bevel cross cutting

8.6 Mitre cuts

9. Maintenance

9.1 Internal Components Map

10. Trouble-shooting

 

1. Declaration of conformity

We declare that this product is in compliance 

with the directive and the standard mentioned 

on the 2. page of this manual.

1.1 Warranty

IGM Tools & Machinery strives to always 

deliver high-quality machinery. The warranty is 

governed by the valid terms and conditions of 

IGM Tools & Machinery available at  

www.igmtools.com.

2. About manual

This manual is intended to thoroughly cover the 

setup up, maintenance, and proper adjustments 

of your new purchase. Aside from the

proceeding general safety considerations, 

this manual DOES NOT cover woodworking 

or metalworking techniques that are possible 

with this product and the appropriate safety 

precautions necessary for safe practices. There 

are several organizations with published safe 

practices, techniques, and proper operation of 

this tool. Or look for handy tips and instructions 

at www.igmtools.com.

3. Fusion 3 specifications

3.1 Contents

Professional Square Zero Clearance Throat 

Plate (pre-installed)  

250 mm Saw Blade (pre-installed) 

Riving Knife (pre-installed)

Mitre Gauge (ships in tool holder)

Tool Holder (pre-installed)  

Fence

Blade Guard 

Arbor Wrench

Installation and Adjustment Tools 

3.2 Technical Data

Power 

230V / 50 Hz / 1 Phase

Motor Type 

TEFC Capacitor Start AC Induction

Power Input 

2200 W

Motor Speed 

2850 /min-1

Full Load Amperage 

14.5 A 

Start Capacitor 

400 µF-U

Run Capacitor 

50 µF-U

Switch Type 

Magnetic with Overload Protection 

Power Transfer 

Single V-Ribbed 142J FJ 

Power Cord 

2 m / H07RNF

Power Plug Included 

CEE 7/7

Breaker Recommendation 

16 A,  

tripping characteristic C (16/1/C) 

General

Footprint (LxW) 

503 x 520 mm

Overall Dimensions (LxWxH) 

1663 mm x 1652 mm x 1081 mm

Shipping Dimensions (LxWxH) 

1130 mm x 1100 mm x 1190 mm

Weight (No Accessories) 

157 Kg

Shipping Weight: 

202 Kg 

Dust Collection: Outlet Dia. 

101.6 mm

Dust Collection m3/h, min. 

934 m3/h

Sound Emissions 

N/A

Specifics

Blade Diameter 

250 mm 

Bore Diameter 

30 mm

Arbor Speed 

3800 /min-1

Blade Rotation 

Counter-Clockwise 

(face arbor)

Rip Capacity, with Fence 

914,4 mm Right (1 320,8 mm w/ accessories)

Max. Depth of Cut 90° 

79 mm

Max. Depth of Cut 45° 

56 mm

Blade Tilt 

45° Left, 3° Arbor Adjustment

Table Dim., with Extensions (LxW) 

1117 mm x 1663 mm

Wing Dimensions (LxW) 

792 x 305 mm

Mitre Slot  

19 and 23 mm, T-Slot

Fence Type 

Sliding Cam Action Fully Adjustable

Fence Dim (LxWxTh.)             670 x 80 x 17 mm

Throat Plate Type   

   Zero Clearance 

Throat Plate (LxWxTh.)     372 x 104.5 x 13 mm

Floor to Table Height                              887 mm

 

 

 

 

 

 

 

 

Pic. 3

 

EN - English

Operating Instructions 

(Laguna manual)

Dear Woodworker,

Thank you for your purchase and welcome to the Laguna Tools group of discerning woodworkers. We understand that you have a 

choice of where to purchase your machines and appreciate the confidence you have in the Laguna Tools brand.

Every machine manufactured by Laguna Tools has been carefully designed and well thought through from a woodworker’s perspective. 

Through hands-on experience, Laguna Tools is constantly working hard to make innovative, precision products. Products that inspire 

you to create works of art, are a joy to run and work on, and encourage your performance.

Содержание LAGUNA Fusion3Dro























Отзывы: