IGM 141-DC30 Скачать руководство пользователя страница 6

-6-

www.igmtools.com

Operating instructions  EN

5.3 Electrical connection

WARNING: 

Make sure the electrical connection 

corresponds to the motor specification (see engine 

cover.) 

WARNING: 

Make sure the switch is in the 

„OFF“ position before turning on the feeder.

A power feeder is an auxiliary machine that 

cooperates with your spindle moulder, table saw or a 

planer.

If you need to use an extension cord; use a 18AWG x 

4C when not exceeding 5 metres and a 16AWG x 4C 

when over 5 metres.

6. SET-UP AND ADJUSTMENT

- Place a 3-4 mm high pad under the output roller 

and slowly run the feeder down until the input roller 

lies on the surface and the output roller is touching 

the pad. Now tighten the screws (K, pic.13) and set 

the scale ring to zero. Tighten the locking pin (H), this 

secures stronger downforce on the infeed roller.

6.1 Basic movements of the feeder

6.1.1 Feeding from the side

- Release the locking lever (A) and turn the feeder off the 

workbench.

- Release the lever (H), grab the handle of the feeder and 

lift the locking pin, turn the feeder to a vertical position. 

Turn it back on the workbench and tighten all the levers.

- The workpiece must be leaning on a guiding fence 

when feeding. The rollers must push the workpiece 

against the fence. The difference between the distance 

of the feeder and the fence should be greater on the 

infeed roller by 3-4 mm than on the outfeed roller (pic. 

15).

6.1.2 Feeding at an angle

- Release the locking lever (A) and turn the feeder off the 

workbench.

- Release screws (K) on the end of the arm, turn the 

positioning joint and set up the required angle (S), and 

then tighten screws (K). (pic.13)

- Release levers (F and G), pull out the locking pin and 

align the feed so that all rollers are in the same height 

over the workbench, then tighten all the levers (pic. 14).

- The workpiece must be leaning on a guiding fence 

when feeding. The rollers must push the workpiece 

against the fence. The difference between the distance 

of the feeder and the fence should be greater on the 

infeed roller by 3-4 mm than on the outfeed roller (pic. 

15).

pic

.12

1

For rotation around the axis of the base: 

release lever (A), and turn the feeder to the 

requested position.

- To extend or compress the arm of the 

feeder: release the lever (B) and 

 

rotate (C).

- To alter the height: release the lever (D) 

and turn the handle (E).

- To rotate the feeder: release the lever

(F) and turn the whole feeder.

- To adjust the angle of the feeder: release 

lever (G). Pull out the locking pin (H) and 

use a handle (1, pic.9) to turn the feeder.

 

Obr. 19 

pic

.14

 

Obr. 20 

X+3~4mm 

 

po

 

 

pic

.15

 

 

 

 

 

pic

.13

Содержание 141-DC30









Отзывы: