Igloo STERYLIS ULTRA-220 Скачать руководство пользователя страница 10

Страница: 10 / 32

STERYLIS ULTRA Operating Manual

WHEN THE STERILISATION PROCESS

IS COMPLETE, IT IS ESSENTIAL

TO VENTILATE THE ROOM FOR

AT LEAST 30 MINUTES!

CAUTION!

Personal protective equipment (ozone)

Hygiene measures

Water and soap

Respiratory protection

Full protective respiratory and eye mask with NO P3 filter (according to

EN 14387)

Eye protection

Full protective mask for the airways and eyes

Hand protection

Chemical-resistant protective gloves

Skin protection

Protective clothing and footwear

Ozone sensor located on the inside

the steriliser allows the current

concentration of ozone in the room

to be tested, so that the controller

can determine the required ozone

time and control the individual

ozone generators accordingly

to maintain the correct ozone

concentration during sterilisation.

The ozone sensor also transmits

information to the controller when

the ozone concentration in the room becomes safe for the user. These are the reasons why the ozone

sensor,

which is an integral part of the device, has to work properly and therefore must not be blocked

by any foreign objects and must be in full contact with the air in the ozoned room

so that their indications

are correct! Improper measurements of the ozone sensor can lead to life-threatening and health-

threatening effects as described in this chapter. The ozone sensor is calibrated by the manufacturer.

Although the sterilisation of

the room will not be completed

before the ozone concentration

of 0.1 ppm (completely safe

for humans) has been reached,

the room must be absolutely

ventilated for at least 30 minutes

after sterilisation.

This is to bring

the ozone level of the room to

100% safe. Please note that the

ozone sensors installed in the

steriliser may fail or the user may undesirably set them off, thus interfering with their measurements. It

should also be borne in mind that the safe level of ozone is different for adults, different for children and

different for animals. Ventilating the device will also allow to get rid of any fog created during the ozone

process (a natural phenomenon) and to get rid of the smell of ozone in the room partially or completely.

Содержание STERYLIS ULTRA-220

































Результаты поиска

Содержание STERYLIS ULTRA-220

Отзывы:

Похожие инструкции для STERYLIS ULTRA-220

Бренды по названию

Популярные бренды

Igloo STERYLIS ULTRA-220, Руководство пользователя

Результаты поиска

Содержание STERYLIS ULTRA-220

Отзывы:

Похожие инструкции для STERYLIS ULTRA-220

Бренды по названию

Популярные бренды