Igema TG32 Скачать руководство пользователя страница 19

 

 

19 

Caution,  if  defects  or  other  damage  arise  during  dismantling,  it  is  essential  that 
they are removed before the gauge is put back into operation, please contact the 
customer service of your contract partner or of IGEMA GmbH. 

 
 

 

7.7.2  Fitting 

 

Fit mica packets with the surface marked “Wasserseite (water side)” 
towards the medium! 
Fit the glasses so that the marking is legible from outside! 

 

 
If a mica disc pack is marked "water side", 
it  must  be  installed  with  the  "water  side" 
marked  side  facing  the  medium!  The 
glasses  must  be  installed  in  such  a  way 
that  the  marking  can  be  read  from  the 
outside! (drawing1, item 7.1) 
 
Grease  the  bolts  (1)  with  a  suitable 
assembly  paste.  Position  graphite  gasket 
(8/11),  borosilicate  glass  (9),  mica  disc 
(10) (only for TG120) and again a graphite 
gasket in the lid rail in this order. Carefully 
place the cover rail (4) with its contents on 
the  base  body  (12)  of  the  indicator  and 
tighten the lateral set screws (7) so firmly 
that they hold the indicator without external 
influence.  The torques and  the tightening 
sequence  according to point  7.1 must  be 
ensured (see drawing). 
 

 

Aufbaudarstellung der Deckelschiene 

 

 

Caution

 

 

Caution 

Содержание TG32





























Отзывы: