IFM TCC8 Series страница 19 Скачать руководство пользователя

Страница: 19 / 21

Displays /

commands

Explanation

Simulation

Simulation of temperature measurement (measuring element

and reference element) and diagnostic cases without opera-

tion

→ 5.5 Simulation mode

�

Protocols

(log entries)

-Device status

-Detailed device status

-Event history

-Operating hours since first set-up

-Operating hours history memory (sampling rate 1 s)

-Internal temperature

-Parameter configuration faults

Binary file transfer

(BLOB)

Command for storing a log file on all calibration check warn-

ings or events

→ 5.6

�

10 Operation

When the supply voltage is applied, the unit is in the RUN mode after a power-on

delay time of 6 s (= normal operating mode)� It carries out its measurement and

evaluation functions and provides output signals according to the set parameters�

11 Technical data

→ Technical data at www.ifm.co.

12 Troubleshooting

The unit has many self-diagnostic options� It monitors itself automatically during

operation

(→ 5.4 Diagnostic function)

�

Diagnostic messages are indicated via the LED (LED blue = warning; LED red =

alarm)�
These messages are also available via IO-Link�

►

Connect the unit to a PC and read it via the IO-Link interface�

►

Carry out corrective measures to restore normal operation�

Содержание TCC8 Series






















Результаты поиска

Содержание TCC8 Series

Отзывы:

Похожие инструкции для TCC8 Series

Бренды по названию

Популярные бренды

IFM TCC8 Series, Руководство по эксплуатации

Результаты поиска

Содержание TCC8 Series

Отзывы:

Похожие инструкции для TCC8 Series

Бренды по названию

Популярные бренды