IFM E30398 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 19

IFM E30398 Скачать руководство пользователя страница 14

14

6.6 Configure the memory plug via LR DEVICE

You need an IO-Link master and the LR DEVICE software to connect the

memory plug with a PC�

►

For connection and set-up, refer to the LR DEVICE operating instructions�

> The following information is displayed in the (LR DEVICE) header�

Write protection is not active:
When the memory plug is connected to a suitable sensor, the

parameters of this sensor will be written in the memory plug�

Write protection is active:
When the memory plug is connected to a suitable sensor, the data set

saved in the memory plug will be written in the sensor�

After reading of a memory plug which contains data,

appears� By

clicking on the icon, the parameters of the saved device are displayed,

if this is supported by the respective device. (→ Display of the data

stored on the memory plug)

appears after clicking on

� By clicking on

the parameter

list of the memory plug is displayed again� The icon changes again to

�

The memory plug only provides memory space for the parameters of one

device�

6.6.1 Store data on the memory plug

►

Read IO-Link parameters from a device using the LR DEVICE software or

select offline parameter setting�

►

Edit parameters�

►

Connect the memory plug to the IO-Link master�

►

Click on [ ] to store data on the memory plug�

The write protection is activated via the system command [Write protect]�

The system command [Read/Write] deactivates the write protection�

«
...
12
13
14
15
16
...
»

Содержание E30398




















Отзывы:

Нет отзывов