background image

DP2200

Analogue threshold display

16

[rP1] follows the changes of [SP1] and keeps the set hysteresis.

8.3.2 FH1/FL1 ─ min/max switching limits for window function

Upper/lower limit for measuring current at which OUT1 switches within the window setting. The
parameters are only displayed if the window function [Fno] or [Fnc] is set in [ou1].

Fno
Fnc

FE

1

0

1

0

FH1

OUT1

I [mA]

FL1

t

Fig. 8: Window functions

FH:

Window upper threshold

FL:

Window lower threshold

FE:

Window

Fno:

Window function normally open

Fnc:

Window function normally closed

u

Select [FH1] and set the upper limit.

u

Select [FL1] and set the lower limit.

[FL1] is always smaller than [FH1]. The device only accepts values which are lower than the
value for [FH1].

[FL1] follows the changes of [FH1] and keeps the set hysteresis.

8.3.3 EF ─ extended functions

EF ─ extended functions: Parameters of the extended functions (EF) (

Ò

 

/

 16)

8.4 Parameters of the extended functions (EF)

8.4.1 rES ─ restore factory setting

Resets all parameters to the Factory settings.

u

Select [rES].

u

Press [●].

u

Press and hold [▲] or [▼] until [----] is displayed.

u

Briefly press [●].

8.4.2 A.Trm ─ analogue termination for OUT2

[OFF] = OUT2 is externally connected, e.g. to the analogue input of another device.

[On] = OUT2 is not connected and the current path is terminated internally.

Note the following for proper current measurement and evaluation:
If the internal analogue termination is set to [On], output OUT2 must not be connected.

8.4.3 ou1 ─ output function for OUT1

Switching signal for the current limits.

[Hno] = hysteresis function / normally open

Содержание DP2200



























Отзывы: