IFM DP2200 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 26

IFM DP2200 Скачать руководство пользователя страница 14

DP2200

Analogue threshold display

14

8 Menu

8.1 General

Irrespective of the operating mode (standard IO mode or IO-Link device) there are two options to set
the parameters of the unit:

•

directly on the device via the menu (

Ò

Parameter setting)

•

or via an IO-Link tool

Access via an IO-Link tool has a higher priority than parameter setting via the menu.

Parameter cloning and parameter setting backup is possible with an IO-Link tool.

Some parameters can only be set via the IO-Link interface:
Parameters adjustable via IO-Link.

If the device was locked via IO-Link, it can also only be unlocked via the IO-Link interface:
Locking / unlocking (

The scaling parameter [ScAL] only influences the display and not the transferred process data or the
actual switching threshold values.

Via IO-Link, the current value is always transmitted in μA → Representation of the measured current
value (

13). The switching thresholds can be set in steps of 0.01 mA.

If a scaling is set, the menu settings of the switching thresholds (SP, rP etc.) are also scaled.
Via IO-Link, however, the settings continue to be displayed and executed in steps of 0.01 mA
(resolution 10 bits).

«
...
12
13
14
15
16
...
»

Содержание DP2200



























Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды