IFM Electronic PG24 Series Скачать руководство пользователя страница 23

Страница: 23 / 27

9.5.2 Reset all parameters to factory setting

►

Select [rES]�

►

Touch [Set] and keep it touched until [----] is displayed�

►

Touch [Mode/Enter] briefly�

It is recommended to take down your own settings in the table before

carrying out a reset

(→ 11 Factory setting)

�

10 Operation

After power on, the unit is in the Run mode (= normal operating mode)� It carries

out its measurement and evaluation functions and provides output signals

according to the set parameters�
Operating indicators

(→ 7 Operating and display elements)

�

Reset the lag indicator (if [LED] = [HInd] or [LInd]):

►

Touch [Set] for 1 second�

> The two lag indicator LEDs jump to the current position of the pointer�

10.1 Read set parameters

►

Touch [Mode/Enter] until the requested parameter is displayed�

►

Touch [Set] briefly�

> The unit displays the corresponding parameter value for about 15 s� After

another 15 s it returns to the Run mode�

10.2 Error indications

[OL]

Overload pressure (measuring range exceeded)�

[UL]

Underload pressure (below measuring range)�

[SC1]

Short circuit in OUT1� The output is switched off as long as the short circuit

persists�

[Err]

Flashing: internal error, invalid entry�

The messages SC1 and Err are displayed even if the display is switched off�

Содержание PG24 Series




























Результаты поиска

Содержание PG24 Series

Отзывы:

Похожие инструкции для PG24 Series

Бренды по названию

Популярные бренды

IFM Electronic PG24 Series, Руководство по эксплуатации

Результаты поиска

Содержание PG24 Series

Отзывы:

Похожие инструкции для PG24 Series

Бренды по названию

Популярные бренды