IFM Electronic LR2059 Скачать руководство пользователя

Страница: 46 / 51

12.6 Change the display unit in the operating mode

Switching between length indication (mm) and percentage.

►

Briefly press [

▲

] or [

▼

] in the operating mode.

> The selected unit is displayed for 30 s, the corresponding LED is on. With each

push of the button the display type is changed.

12.7 Error indications

Possible cause

Recommended measures

[Err]

Fault in the electronics.

Replace the unit.

[nPrb]

Probe detached from the unit;

possibly incorrect setting of the

probe length.

Check whether the probe is still

attached to the unit. Check the

parameter [LEnG].

[SEnS]

Measurement disturbed

by heavy foam build-up or

turbulence.

• Install the unit in a still pipe or

bypass

(→ 7.1)

• Set / increment [dFo]

(→ 11.4.11)

Measurement disturbed by

separation layers (e.g. oil layer

on water).

• Remove oil by suction.

• Stir the medium.

• Check the composition.

Probe or process connection

soiled.

Clean the probe and the process

connection.

Installation conditions not

adhered to.

• Follow the installation instructions

(→ 7)

• Carry out or repeat a tank

adjustment

(→ 11.2.4)

Probe length or sensitivity

(setting to the medium) incorrect.

Correct settings

(→ 11.6)

, then carry out tank

adjustment, if necessary

(→ 11.2.4)

[SCx] + LED 7

[SCx] + LED 8

Flashing: short circuit in

switching output OUT1 or OUT2. Remove the short circuit.

[SC] + LED 7

+ LED 8

Flashing: short circuit in both

switching outputs.

Remove the short circuit.

[PArA]

Faulty data set

Reset to factory settings

(→ 11.5)

Содержание LR2059




















































Результаты поиска

Содержание LR2059

Отзывы:

Похожие инструкции для LR2059

Бренды по названию

Популярные бренды

IFM Electronic LR2059, Руководство по эксплуатации

Результаты поиска

Содержание LR2059

Отзывы:

Похожие инструкции для LR2059

Бренды по названию

Популярные бренды