IES Wallbox G3 Скачать руководство пользователя страница 35

Страница: 35 / 40

www.ies-synergy.com

Installation Manual

DIM016055-EN

Booting errors

Message

Description

Error connecting server.

Message displayed during the startup of the

charging station if the backend server reject the

connection.

Error connecting to rfid reader.

Message displayed during the startup of the

charging station if the RFID does not work. Please

see the maintenance manual.

Error connecting to comm control unit.

Message displayed during the startup of the

charging station if the CCU does not work. Please

see the maintenance manual.

Power limitation

If necessary, you can limit the power delivered by the charging station on the backend server.

For the charging station, use the OCPP frame “Change Configuration” to adjust the following configuration

parameters:

Configuration parameters

details

Expected

v a l u e

type

D e f a u l t

value

Description

PowerLimit

Watts

24000

Maximum power to be delivered by the charger. Al-

low to limit the output power below 24kW.

VoltageSupplyLimit

Volt

230

The nominal value of the single-phase voltage pro-

vided in the country. Usually 230V in Europe.

CurrentInputLimit

Amp

The maximum current allowed by the power supply

installation (value of the circuit-breaker installed

outside the charger).

Refer to your backend server instructions to know how to change these configuration parameters.

Содержание Wallbox G3









































Результаты поиска

Содержание Wallbox G3

Отзывы:

Похожие инструкции для Wallbox G3

Бренды по названию

Популярные бренды

IES Wallbox G3, Руководство по установке

Результаты поиска

Содержание Wallbox G3

Отзывы:

Похожие инструкции для Wallbox G3

Бренды по названию

Популярные бренды