IES Wallbox G3 Скачать руководство пользователя страница 14

Страница: 14 / 40

www.ies-synergy.com

Installation Manual

DIM016055-EN

Embedded Insulation device

Line L+/L- Voltage (Un)

DC 150V…530V

System leakage capacity Ce

≤ 1µF : response value (Ran) and time (tan) are not guar

anteed for capacity above 1µF

Parallelization

Warning:

Do not connect the insulation monitor de-

vice (IMD) in parallel !!

Response value (Ran) and time (tan) are not guaranteed.

General & dimensions

External dimensions (mm)

H x W x D

860 x 507 x 250 mm

Weight (without cable, or bracket)

66kg

Max

Type of installation

Mounting on a wall or on a pedestal with

proper fixation point

Fixation points

8 screws for wall mounting

Protection type (EN60529)

IP54

Cooling systems

Heatsink with forced air flow by fans IP55

without air filter

Noise (1m, all direction)

Db(A)

65dbA (1m)

Climatic & Environment constraints

Operating temperature (with derating)

-25°C to +55°C

(4)

Storage temperature

-25°C to +60°C

Relative humidity

10% to 95%

Installation altitude

Alt

2 000m

Max

Norms & standards

EC Low voltage EC directive (LVD)

2014/35/EU

EC Electromagnetic Directive (EMC)

2014/30/EU

Radio Equipment Directive (RED)

2014/53/EU

Electric vehicle conductive charging system part 1

General requirement

IEC 61851-1

Electric vehicle conductive charging system part 23

DC Electric vehicle charging station

IEC 61851-23

EMC requirement for OFF board electric vehicle charging

system

IEC 61851-21-2

Insulation Monitor Device (IMD)

IEC 61557-1 & IEC 61557-8

RoHS

2015/863/EU

Declaration of conformity CE

(5)

Yes

(1)

EC approval pending.

(2)

Max output current will be adapted versus maximum carrying current of the vehicle plug.

(3)

Output current can be even reduced with the power derating versus temperature.

(4)

Potential derating above 35°C.

(5)

CE marking affixed on the product attest the conformity of the product with applicable requirements of rele-

vent Community harmonization legislation.

Содержание Wallbox G3









































Результаты поиска

Содержание Wallbox G3

Отзывы:

Похожие инструкции для Wallbox G3

Бренды по названию

Популярные бренды

IES Wallbox G3, Руководство по установке

Результаты поиска

Содержание Wallbox G3

Отзывы:

Похожие инструкции для Wallbox G3

Бренды по названию

Популярные бренды