manualshive.com logo in svg

IEI Technology WAFER-945GSELVDS2-N270-R10, Руководство пользователя

Поделиться
Скачать
IEI Technology WAFER-945GSELVDS2-N270-R10 Скачать руководство пользователя страница 62

 

 

WAFER-945GSELVDS2

Page 50 

 

Figure 4-5: CF Card Setup Jumper Location 

4.6.4 Clear CMOS Jumper 

Jumper Label: 

J_CMOS1 

Jumper Type: 

3-pin header 

Jumper Settings: 

See Table 4-5 

Jumper Location: 

See Figure 4-6 

If the WAFER-945GSELVDS2 fails to boot due to improper BIOS settings, the clear 

CMOS jumper clears the CMOS data and resets the system BIOS information. To do this, 

use the jumper cap to close pins 2 and 3 for a few seconds then reinstall the jumper clip 

back to pins 1 and 2. 

If the “CMOS Settings Wrong” message is displayed during the boot up process, the fault 

may be corrected by pressing the F1 to enter the CMOS Setup menu.    Do one of the 

following: 

ƒ

 

Enter the correct CMOS setting 

ƒ

 

Load Optimal Defaults 

ƒ

 

Load Failsafe Defaults.     

After having done one of the above, save the changes and exit the CMOS Setup menu.   

The clear CMOS jumper settings are shown in 

Table 4-5

. 

Содержание WAFER-945GSELVDS2-N270-R10













































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды