IEI Technology WAFER-945GSELVDS2-N270-R10 Скачать руководство пользователя страница 106

Страница: 106 / 140

WAFER-945GSELVDS2

Page 94

Legacy USB Support [Enabled]

Use the

Legacy USB Support

BIOS option to enable USB mouse and USB keyboard

support.

Normally if this option is not enabled, any attached USB mouse or USB keyboard does not

become available until a USB compatible operating system is fully booted with all USB

drivers loaded. When this option is enabled, any attached USB mouse or USB keyboard

can control the system even when there is no USB driver loaded onto the system.

Disabled

Legacy USB support disabled

Enabled D

EFAULT

Legacy USB support enabled

Auto

Legacy USB support disabled if no USB devices are

connected

USB2.0 Controller Mode [HiSpeed]

Use the

USB2.0 Controller Mode

option to set the speed of the USB2.0 controller.

FullSpeed

The controller is capable of operating at 12 Mb/s

HiSpeed D

EFAULT

The controller is capable of operating at 480 Mb/s

Содержание WAFER-945GSELVDS2-N270-R10













































































































































Результаты поиска

Содержание WAFER-945GSELVDS2-N270-R10

Отзывы:

Бренды по названию

Популярные бренды

IEI Technology WAFER-945GSELVDS2-N270-R10, Руководство пользователя

Результаты поиска

Содержание WAFER-945GSELVDS2-N270-R10

Отзывы:

Бренды по названию

Популярные бренды