IEI Technology WAFER-8523 Скачать руководство пользователя

Страница: 99 / 177

WAFER-8523 User Manual

Page 84

BIOS Menu 5: IDE Master and IDE Slave Configuration

Auto-Detected Drive Parameters

The “grayed-out” items in the left frame are IDE disk drive parameters automatically

detected from the firmware of the selected IDE disk drive. The drive parameters are listed

as follows:

Device

: Lists the device type (e.g. hard disk, CD-ROM etc.)

Type

: Indicates the type of devices a user can manually select

Vendor

: Lists the device manufacturer

Size

: List the storage capacity of the device.

LBA Mode

: Indicates whether the LBA (Logical Block Addressing) is a

method of addressing data on a disk drive is supported or not.

Block Mode

: Block mode boosts IDE drive performance by increasing the

amount of data transferred. Only 512 bytes of data can be transferred per

interrupt if block mode is not used. Block mode allows transfers of up to 64 KB

per interrupt.

PIO Mode

: Indicates the PIO mode of the installed device.

Async DMA

: Indicates the highest Asynchronous DMA Mode that is

supported.

Ultra DMA

: Indicates the highest Synchronous DMA Mode that is supported.

S.M.A.R.T.

: Indicates whether or not the Self-Monitoring Analysis and

Reporting Technology protocol is supported.

Содержание WAFER-8523


















































































































































































Результаты поиска

Содержание WAFER-8523

Отзывы:

Похожие инструкции для WAFER-8523

Бренды по названию

Популярные бренды

IEI Technology WAFER-8523, Руководство пользователя

Результаты поиска

Содержание WAFER-8523

Отзывы:

Похожие инструкции для WAFER-8523

Бренды по названию

Популярные бренды