background image

 

PAC-1000G QIG                    IEI Technology Corp.                                    Page  6 

 
 

 
S

TEP 

7.1: D

RIVE 

B

RACKET 

R

EMOVAL

 

 
To remove the drive bracket, please follow the steps below: 
 

Step 1: 

Remove the four drive bracket retention screws from the 
right side of the chassis. 

 

 

Figure 14:  Four Side Drive Bracket Retention Screws 

 

Step 2: 

Remove the one internal drive bracket retention screw 
from the top of the fan bracket. 

 

 

Figure 15:

 

Internal Drive Bracket Retention Screw

 

 
S

TEP 

7.2: I

NTERNAL 

HDD I

NSTALLATION

 

 
The PAC-1000G can support an HDD to be installed on the 
right side of the drive bracket. To install a 3.5” HDD into the 
right side of the drive bracket, please follow the steps below. 

Step 1: 

Remove the drive bracket. To do this, please 

refer to

 

S

TEP 

8.1: D

RIVE 

B

RACKET 

R

EMOVAL

Step 2: 

Slide a 3.5” HDD into the 3.5” drive bay. Make 
sure both the 4-pin power connector and the 
IDE/SATA connecter are at the rear of the drive 
bracket. 

Step 3: 

To secure the 3.5” drive to the drive bracket, 
insert four retention screws, two on each side.

Step 0:

   

 

Figure 16: Secure an HDD to the Right Side of the Drive 

Bracket 

S

TEP 

7.3: FDD/HDD

 

I

NSTALLATION

 

To install a 3.5” FDD/HDD into the 3.5” front accessible drive 
bracket, please follow the steps below: 

Step 1: 

Slide a 3.5” FDD/HDD into the 3.5” FDD drive bay. 
Make sure both the 4-pin power connector and 
the IDE/SATA connector are at the rear of the 
drive bracket. 

Step 2: 

Align the retention screw holes in the 3.5” 
FDD/HDD drive with the retention screw holes in 
the 3.5” front accessible drive bay. 

Step 3: 

Insert four retention screws, two on each side to 
secure the 3.5” FDD/HDD to the drive bracket. 

 

Figure 17: Secure a 3.5

FDD to the 3.5

Drive Bay

S

TEP 

7.4: O

PTICAL 

D

RIVE 

I

NSTALLATION

 

 
To install a 5.25” drive into the drive bracket, please follow 
the steps below. 

Step 1: 

Remove the drive bracket. To do this, please 

refer to 

S

TEP 

8.1: D

RIVE 

B

RACKET 

R

EMOVAL

.

 

Step 2: 

Slide a 5.25” optical drive into the 5.25” drive bay 
making sure both the 4-pin power connector and 
the IDE/SATA connector are at the rear of the 
drive bracket. 

Step 3: 

Insert four retention screws, two on each side of 
the drive bay to secure the 5.25” optical drive.

 

Step 0:

 

Содержание PAC-1000G











Отзывы: