IEI Technology Nova-lx Скачать руководство пользователя страница 44

Страница: 44 / 225

NOVA-LX 5.25” Motherboard

Page 24

2.5.3.2 Super I/O Hardware Monitor Functions

The Super I/O Hardware Monitor monitors internal voltages, system temperature and the

cooling fan speed. All the monitored environmental parameters can be read from the BIOS

Hardware Health Configuration menu.

2.5.3.3 Super I/O Parallel Port

The Super I/O parallel port (LPT) is compatible with the following LPT specifications.

IBM parallel port compatible

PS/2 compatible bi-directional parallel port

Enhanced Parallel Port (EPP) mode supported. Compatible with IEEE 1284

specifications

Extended Parallel Port (EPP) mode supported. Compatible with IEEE 1284

specifications

Enhanced printer port back-drive current protection

The parallel port controller is connected to an external DB-26 LPT connector.

2.5.3.4 Super I/O Floppy Disk Drive (FDD) Controller

The Super I/O FDD controller is compatible with the following specifications.

IBM PC AT disk drive compatible

Variable write pre-compensation with track selectable capability

Vertical recording format supported

DMA logic enabled

16-byte data FIFOs

Overrun and under run conditions detected

Built-in address mark detection circuitry to simplify the read electronics

FDD anti-virus functions with software write protect and FDD write enable

signal

Supports 3.5-inch or 5.25-inch FDD

Compatible with industry standard 82077

Supported capacities:

360K

Содержание Nova-lx


































































































































































































































Результаты поиска

Содержание Nova-lx

Отзывы:

Похожие инструкции для Nova-lx

Бренды по названию

Популярные бренды

IEI Technology Nova-lx, Руководство пользователя

Результаты поиска

Содержание Nova-lx

Отзывы:

Похожие инструкции для Nova-lx

Бренды по названию

Популярные бренды