IEI Technology NANO-PV-D510A Скачать руководство пользователя страница 82

Страница: 82 / 169

NANO-PV-D510A User Manual

Page 68

Frequency: Lists the CPU processing speed

FSB Speed: Lists the FSB speed

Cache L1: Lists the CPU L1 cache size

Cache L2: Lists the CPU L2 cache size

5.3.2 IDE Configuration

Use the

IDE Configuration

menu (

BIOS Menu 4

) to change and/or set the configuration

of the IDE devices installed in the system.

BIOS SETUP UTILITY

Main

Advanced

PCIPNP

Boot

Security

Chipset

Exit

IDE Configuration

⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯

ATA/IDE Configuration

[Enhanced]

Configure SATA as

[IDE]

> Primary IDE Master

: [Not Detected]

> Primary IDE Slave

: [Not Detected]

> Secondary IDE Master

: [Not Detected]

> Secondary IDE Slave

: [Not Detected]

> Third IDE Master

: [Not Detected]

> Third IDE Slave

: [Not Detected]

DISABLED: disable the
integrated IDE
controller.
PRIMARY: enables only
the Primary IDE
controller
SECONDARY: enables only
the Secondary IDE
controller.
BOTH: enables both IDE
controllers

Select

Screen

↑

↓

Select

Item

Enter Go to SubScreen
F1 General

Help

F10

Save and Exit

ESC Exit

BIOS Menu 4: IDE

Configuration

ATA/IDE Configurations [Compatible]

Use the

ATA/IDE Configurations

option to configure the ATA/IDE controller.

Disabled

Disables the on-board ATA/IDE controller.

Compatible

Configures the on-board ATA/IDE controller to be in

compatible mode. In this mode, a SATA channel will

replace one of the IDE channels. This mode supports

up to 4 storage devices.

Содержание NANO-PV-D510A










































































































































































Результаты поиска

Содержание NANO-PV-D510A

Отзывы:

IEI Technology NANO-PV-D510A, Руководство пользователя, Страница: 82 / 169

Результаты поиска

Содержание NANO-PV-D510A

Отзывы: