IEI Technology NANO-PV-D510A Скачать руководство пользователя страница 16

Страница: 16 / 169

NANO-PV-D510A User Manual

Page 2

1.1 Introduction

Figure 1-1: NANO-PV-D510A

The NANO-PV-D510A EPIC CPU card is an embedded 45 nm Intel® Atom™ processor

platform. The Intel® Atom™ dual-core processor D510 embedded on the

NANO-PV-D510A has a 1.66 GHz clock speed, and a 1 MB L2 cache. The

NANO-PV-D510A supports one 200-pin 667/800 MHz 2.0 GB (max.) DDR2 SDRAM

SO-DIMM. The board includes one LVDS connector (supports an 18-bit single-channel

LVDS screen), one VGA connector, and supports a dual-display configuration. The

NANO-PV-D510A also comes with two Gigabit Ethernet (GbE) connectors, two SATA

connectors, eight USB 2.0 connectors, one PCI-104 slot, one PCIe Mini Card slot, three

RS-232 connectors, one RS-232/422/485 and one CompactFlash® Type II slot.

1.2 Features

Some of the NANO-PV-D510A motherboard features are listed below:

EPIC form factor

RoHS

compliant

PCI-104 and PCIe expansion slots

Supports one DDR2 SO-DIMM up to 2.0 GB

Two Gigabit Ethernet controllers

Supports 8 USB 2.0 ports

Содержание NANO-PV-D510A










































































































































































Результаты поиска

Содержание NANO-PV-D510A

Отзывы:

IEI Technology NANO-PV-D510A, Руководство пользователя, Страница: 16 / 169

Результаты поиска

Содержание NANO-PV-D510A

Отзывы: