IEI Technology NANO-PV-D510A Скачать руководство пользователя страница 120

Страница: 120 / 169

NANO-PV-D510A User Manual

Page 106

Change Supervisor Password

Use the

Change Supervisor Password

to set or change a supervisor password. The

default for this option is

Not Installed

. If a supervisor password must be installed, select

this field and enter the password. After the password has been added,

Install

appears

next to

Change Supervisor Password

Change User Password

Use the

Change User Password

to set or change a user password. The default for this

option is

Not Installed

. If a user password must be installed, select this field and enter the

password. After the password has been added,

Install

appears next to

Change User

Password

Clear User Password

Use the

Clear User Password

to clear a user’s password. The default for this option is

Not Installed

. If a user password must be cleared, use this option.

Boot Sector Virus Protection [Disabled]

Use the

Boot Sector Virus Protection

to enable or disable boot sector protection.

Disabled D

EFAULT

Disables the boot sector virus protection

Enabled

Enables the boot sector virus protection

5.7 Chipset

Use the

Chipset

menu (

BIOS Menu 23

) to access the Northbridge and Southbridge

configuration menus

WARNING!

Setting the wrong values for the Chipset BIOS selections in the Chipset

BIOS menu may cause the system to malfunction.

Содержание NANO-PV-D510A










































































































































































Результаты поиска

Содержание NANO-PV-D510A

Отзывы:

IEI Technology NANO-PV-D510A, Руководство пользователя, Страница: 120 / 169

Результаты поиска

Содержание NANO-PV-D510A

Отзывы: