IEI Technology LCD-KIT150G Скачать руководство пользователя

Страница: 4 / 126

Page 4

IEI® Technology, Corp

Condensation might form inside the monitor chassis if exposed to sudden

changes in temperature.

Carefully route the power cord so that people cannot step on it. Do not place

anything over the power cord.

If the equipment should be left unused for an extended period of time, disconnect

it from the power source to avoid damage by transient over-voltage.

If any of the following situations arise, have the equipment checked by qualified

service personnel:

The power cord or plug is damaged.

Liquid has penetrated into the equipment.

The equipment has been exposed to moisture.

The equipment does not work properly, or cannot be made to work

according to the user manual.

The equipment has been dropped and damaged.

The equipment shows obvious signs of damage.

WARNING!

Any changes or modifications made to the equipment that are not

expressly approved by the relevant standards could void the authority to

operate the equipment.

ADDITIONAL INFORMATION AND ASSISTANCE

MAINTENANCE AND CLEANING

Prior to cleaning any part or component of the monitor, please read the details below.

Except for the properly installed front LCD panel, never spray or squirt liquids

directly onto any other component. To clean the LCD panel, please rub it with a

piece of soft dry cloth or a slightly moistened cloth.

The interior of the LCD monitor does not require cleaning. Keep fluids away from

the LCD monitor interior.

Содержание LCD-KIT150G































































































































Результаты поиска

Содержание LCD-KIT150G

Отзывы:

Похожие инструкции для LCD-KIT150G

Бренды по названию

Популярные бренды

IEI Technology LCD-KIT150G, Руководство пользователя

Результаты поиска

Содержание LCD-KIT150G

Отзывы:

Похожие инструкции для LCD-KIT150G

Бренды по названию

Популярные бренды