IEI Technology ITG-100-AL Скачать руководство пользователя страница 71

Страница: 71 / 107

ITG-100-AL Embedded System

Page 59



Disabled

EFAULT

Disabled the auto recovery function



Enabled

Enabled the auto recovery function

5.3.9 SATA Configuration

Use the

SATA Configuration

menu (

BIOS Menu 13

) to change and/or set the

configuration of the SATA devices installed in the system.

Advanced

SATA Configuration

SATA Mode Selection

[ACHI]

SATA Port0

Not Present

Hot Plug

[Disabled]

mSATA Port

BIWIN SSD (31.6GB)

Hot Plug

[Disabled]

Determines how SATA
controller(s) operate.

---------------------



: Select Screen

↑

↓

: Select Item

Enter

Select

General Help

Previous Values

Optimized

Defaults
F4

Save

ESC

Exit

BIOS Menu 13: IDE

Configuration



SATA Mode Selection [AHCI]

Use the

SATA Mode Selection

option to configure SATA devices as normal IDE devices.



AHCI

EFAULT

Configures SATA devices as AHCI device.



Hot Plug [Disabled]

Use the

Hot Plug

option to configure the port as Hot Pluggable.



Disabled

EFAULT

Disables the port as Hot Pluggable.



Enabled

Enables the port as Hot Pluggable.

Содержание ITG-100-AL












































































































Результаты поиска

Содержание ITG-100-AL

Отзывы:

Бренды по названию

Популярные бренды

IEI Technology ITG-100-AL, Руководство пользователя

Результаты поиска

Содержание ITG-100-AL

Отзывы:

Бренды по названию

Популярные бренды